[4294667.296000] Primary instruction cache 32kB, physically tagged, 2-way, linesize 64 bytes.
[4294667.296000] Primary data cache 64kB, 4-way, linesize 64 bytes.
[4294667.296000] Synthesized TLB refill handler (23 instructions).
[4294667.296000] Synthesized TLB load handler fastpath (37 instructions).
[4294667.296000] Synthesized TLB store handler fastpath (37 instructions).
[4294667.296000] Synthesized TLB modify handler fastpath (36 instructions).
[4294667.296000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[4294667.296000] Found MIPS counter frequency: 203 Mhz
[4294667.296000] Using 202.501 MHz high precision timer.
[4294667.296000] Console: colour dummy device 80x25
[4294667.303000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[4294667.303000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[4294667.316000] Memory: 137088k/262144k available (2811k kernel code, 124828k reserved, 610k data, 140k init, 0k highmem)
[4294667.317000] Calibrating delay loop... 402.43 BogoMIPS (lpj=201216)
[4294667.338000] Mount-cache hash table entries: 512
[4294667.339000] Checking for 'wait' instruction...  available.
[4294667.339000] plat_prepare_cpus: ENABLING 2nd Thread...
[4294667.340000] TP0: prom_boot_secondary: Kick off 2nd CPU...
[4294667.342000] CPU revision is: 0002a044
[4294667.342000] FPU revision is: 00130001
[4294667.342000] Primary instruction cache 32kB, physically tagged, 2-way, linesize 64 bytes.
[4294667.342000] Primary data cache 64kB, 4-way, linesize 64 bytes.
[4294667.342000] Synthesized TLB refill handler (23 instructions).
[4294667.342000] Calibrating delay loop... 404.48 BogoMIPS (lpj=202240)
[4294667.363000] Brought up 2 CPUs
[4294667.415000] migration_cost=1000
[4294667.418000] NET: Registered protocol family 16
[4294667.419000] registering PCI controller with io_map_base unset
[4294667.420000] registering PCI controller with io_map_base unset
[4294667.422000] SCSI subsystem initialized
[4294667.422000] usbcore: registered new driver usbfs
[4294667.423000] usbcore: registered new driver hub
[4294667.425000] NET: Registered protocol family 2
[4294667.437000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[4294667.438000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[4294667.439000] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[4294667.440000] TCP: Hash tables configured (established 8192 bind 4096)
[4294667.441000] TCP reno registered
[4294667.441000] brcm-pm: disabling power to USB block
[4294667.442000] brcm-pm: disabling power to ENET block
[4294667.443000] brcm-pm: disabling power to SATA block
[4294667.446000] JFFS2 version 2.2. (NAND) (SUMMARY)  (C) 2001-2006 Red Hat, Inc.
[4294667.447000] Initializing Cryptographic API
[4294667.448000] io scheduler noop registered
[4294667.448000] io scheduler anticipatory registered
[4294667.449000] io scheduler deadline registered
[4294667.449000] io scheduler cfq registered (default)
[4294667.454000] Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
[4294667.455000] serial8250: ttyS0 at MMIO 0x0 (irq = 22) is a 16550A
[4294667.456000] serial8250: ttyS1 at MMIO 0x0 (irq = 67) is a 16550A
[4294667.457000] brcm-pm: enabling power to ENET block
[4294667.458000] Broadcom BCM7413 P21 Ethernet Network Device v2.0 Feb  8 2011 10:23:01
[4294667.460000] Config Internal PHY Through MDIO: 100 MB Full-Duplex (auto-neg)
[4294669.207000] libata version 2.00 loaded.
[4294669.207000] brcm-pm: enabling power to SATA block
[4294669.207000] sata_svw 0000:01:00.0: version 4.0
[4294669.224000] ata1: SATA max UDMA/133 cmd 0xB0510100 ctl 0xB0510120 bmdma 0xB0510130 irq 42
[4294669.225000] ata2: SATA max UDMA/133 cmd 0xB0510000 ctl 0xB0510020 bmdma 0xB0510030 irq 42
[4294669.226000] scsi0 : sata_svw
[4294669.534000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl F0000)
[4294669.550000] ata1.00: ATA-8, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 0/32)
[4294669.561000] ata1.00: configured for UDMA/133
[4294669.561000] scsi1 : sata_svw
[4294669.865000] ata2: SATA link down (SStatus 4 SControl 300)
[4294669.897000] ATA: abnormal status 0x7F on port 0xb051001c
[4294669.898000]   Vendor: ATA       Model: SAMSUNG HM250HI   Rev: 2AC1
[4294669.899000]   Type:   Direct-Access                      ANSI SCSI revision: 05
[4294669.900000] SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
[4294669.901000] sda: Write Protect is off
[4294669.901000] sda: Mode Sense: 00 3a 00 00
[4294669.901000] SCSI device sda: drive cache: write back
[4294669.902000] SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
[4294669.903000] sda: Write Protect is off
[4294669.903000] sda: Mode Sense: 00 3a 00 00
[4294669.903000] SCSI device sda: drive cache: write back
[4294669.904000]  sda: sda1
[4294669.930000] sd 0:0:0:0: Attached scsi disk sda
[4294669.931000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[4294669.932000] Broadcom STB NAND controller (BrcmNand Controller)
[4294669.933000] NAND_CS_NAND_XOR=00000000
[4294669.933000] brcmnand_probe: CS0: dev_id=ad76ad76
[4294669.934000] After: NandSelect=40000002, nandConfig=04042300
[4294669.935000] NAND Config: Reg=04042300, chipSize=64 MB, blockSize=16K, erase_shift=e
[4294669.936000] busWidth=1, pageSize=512B, page_shift=9, page_mask=000001ff
[4294669.936000] timing1 not adjusted: 5363444f
[4294669.937000] timing2 not adjusted: 00000fc6
[4294669.938000] BrcmNAND mfg ad 76 Hynix HY27US08121A (dream) 64MB
[4294669.938000] 
[4294669.938000] Found NAND: ACC=00000010, cfg=04042300, flashId=ad76ad76, tim1=5363444f, tim2=00000fc6
[4294669.940000] BrcmNAND version = 0x0302 64MB @00000000
[4294669.940000] B4: NandSelect=40000002, nandConfig=04042300, chipSelect=-1
[4294669.940000] brcmnand_probe: CS-1: dev_id=ad76ad76
[4294669.941000] After: NandSelect=40000002, nandConfig=04042300
[4294669.941000] Found NAND chip on Chip Select -1, chipSize=64MB, usable size=64MB, base=0x
[4294669.942000] brcmnand_scan: B4 nand_select = 40000002
[4294669.943000] brcmnand_scan: After nand_select = 40000002
[4294669.944000] page_shift=9, bbt_erase_shift=14, chip_shift=26, phys_erase_shift=14
[4294669.945000] Brcm NAND controller version = 3.2 NAND flash size 64MB @1c000000
[4294669.945000] mtd->oobsize=16, mtd->eccOobSize=16
[4294669.946000] brcmnand_scan:  mtd->oobsize=16
[4294669.946000] brcmnand_scan: oobavail=12, eccsize=512, writesize=512
[4294669.947000] brcmnand_scan, eccsize=512, writesize=512, eccsteps=1, ecclevel=15, eccbytes=3
[4294669.948000] brcmnand_default_bbt: bbt_td = bbt_main_descr
[4294669.949000] Bad block table found at page 1ffe0, version 0x01
[4294669.950000] Bad block table found at page 1ffc0, version 0x01
[4294669.951000] brcmnandCET: Status -> Deferred
[4294669.951000] 	numchips=1, size=4000000
[4294669.952000] Creating 4 MTD partitions on "bcm7xxx-nand.0":
[4294669.952000] 0x0000000000000000-0x0000000004000000 : "complete"
[4294669.956000] 0x0000000000000000-0x0000000000040000 : "loader"
[4294669.957000] 0x0000000000040000-0x0000000000400000 : "boot partition"
[4294669.959000] 0x0000000000400000-0x0000000004000000 : "root partition"
[4294669.963000] ehci_hcd_brcm_init: Initializing 2 EHCI controller(s)
[4294669.963000] brcm-pm: enabling power to USB block
[4294669.964000] 10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (EHCI-brcm-0)
[4294669.965000] drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller
[4294669.966000]  - USB h/w setup mode <B>
[4294669.966000]  - USB power enable set for active LOW mode
[4294669.967000] brcm-ehci brcm-ehci.0: BRCM EHCI
[4294669.968000] brcm-ehci brcm-ehci.0: new USB bus registered, assigned bus number 1
[4294669.969000] brcm-ehci brcm-ehci.0: irq 62, io mem 0x10480300
[4294669.969000] brcm-ehci brcm-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
[4294669.971000] usb usb1: configuration #1 chosen from 1 choice
[4294669.971000] hub 1-0:1.0: USB hub found
[4294669.972000] hub 1-0:1.0: 2 ports detected
[4294670.074000] 10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (EHCI-brcm-1)
[4294670.075000] drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller
[4294670.076000] brcm-ehci-1 brcm-ehci-1.1: BRCM EHCI
[4294670.076000] brcm-ehci-1 brcm-ehci-1.1: new USB bus registered, assigned bus number 2
[4294670.077000] brcm-ehci-1 brcm-ehci-1.1: irq 57, io mem 0x10480500
[4294670.078000] brcm-ehci-1 brcm-ehci-1.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
[4294670.079000] usb usb2: configuration #1 chosen from 1 choice
[4294670.080000] hub 2-0:1.0: USB hub found
[4294670.081000] hub 2-0:1.0: 2 ports detected
[4294670.182000] ohci_hcd_brcm_init: Initializing 2 OHCI controller(s)
[4294670.183000] 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-0)
[4294670.184000] drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
[4294670.184000]  - Resetting at b0480408
[4294670.185000] <-- brcm_start_hc
[4294670.185000] brcm-ohci-0 brcm-ohci-0.0: BRCM OHCI
[4294670.186000] brcm-ohci-0 brcm-ohci-0.0: new USB bus registered, assigned bus number 3
[4294670.187000] brcm-ohci-0 brcm-ohci-0.0: irq 63, io mem 0x10480400
[4294670.243000] usb usb3: configuration #1 chosen from 1 choice
[4294670.244000] hub 3-0:1.0: USB hub found
[4294670.244000] hub 3-0:1.0: 2 ports detected
[4294670.280000] usb 1-1: new high speed USB device using brcm-ehci and address 2
[4294670.346000] 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-1)
[4294670.347000] drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
[4294670.348000]  - Resetting at b0480608
[4294670.348000] <-- brcm_start_hc
[4294670.349000] brcm-ohci-1 brcm-ohci-1.1: BRCM OHCI
[4294670.349000] brcm-ohci-1 brcm-ohci-1.1: new USB bus registered, assigned bus number 4
[4294670.350000] brcm-ohci-1 brcm-ohci-1.1: irq 64, io mem 0x10480600
[4294670.396000] usb 1-1: configuration #1 chosen from 1 choice
[4294670.398000] hub 1-1:1.0: USB hub found
[4294670.398000] hub 1-1:1.0: 4 ports detected
[4294670.406000] usb usb4: configuration #1 chosen from 1 choice
[4294670.407000] hub 4-0:1.0: USB hub found
[4294670.407000] hub 4-0:1.0: 2 ports detected
[4294670.509000] Initializing USB Mass Storage driver...
[4294670.680000] usb 1-1.1: new high speed USB device using brcm-ehci and address 3
[4294670.868000] usb 1-1.1: configuration #1 chosen from 1 choice
[4294670.871000] scsi2 : SCSI emulation for USB Mass Storage devices
[4294670.872000] usb-storage: device found at 3
[4294670.872000] usbcore: registered new driver usb-storage
[4294670.872000] USB Mass Storage support registered.
[4294670.872000] i2c /dev entries driver
[4294670.872000] Advanced Linux Sound Architecture Driver Version 1.0.12rc1 (Thu Jun 22 13:55:50 2006 UTC).
[4294670.872000] ALSA device list:
[4294670.872000]   No soundcards found.
[4294670.875000] usb-storage: waiting for device to settle before scanning
[4294670.875000] TCP bic registered
[4294670.876000] NET: Registered protocol family 1
[4294670.876000] NET: Registered protocol family 17
[4294675.875000] isa bounce pool size: 16 pages
[4294676.082000]   Vendor: General   Model: USB Flash Disk    Rev: 1100
[4294676.083000]   Type:   Direct-Access                      ANSI SCSI revision: 00
[4294676.085000] SCSI device sdb: 7864320 512-byte hdwr sectors (4027 MB)
[4294676.087000] sdb: Write Protect is off
[4294676.087000] sdb: Mode Sense: 43 00 00 00
[4294676.087000] sdb: assuming drive cache: write through
[4294677.412000] VFS: Mounted root (jffs2 filesystem).
[4294677.412000] Freeing unused kernel memory: 140k freed
[4294677.415000] SCSI device sdb: 7864320 512-byte hdwr sectors (4027 MB)
[4294677.417000] sdb: Write Protect is off
[4294677.417000] sdb: Mode Sense: 43 00 00 00
[4294677.417000] sdb: assuming drive cache: write through
[4294677.418000]  sdb: sdb1
[4294677.419000] sd 2:0:0:0: Attached scsi removable disk sdb
[4294677.420000] sd 2:0:0:0: Attached scsi generic sg1 type 0
[4294677.429000] usb-storage: device scan complete
[4294678.353000] stb_core: module license 'Proprietary' taints kernel.
[4294678.506000] 4006177 ms: 
[4294678.599000] 92 ms: 27 Starting /etc/rcS.d/S02sysfs...
[4294678.608000] 8 ms: =s
[4294679.886000] 1277 ms: 29 Starting /etc/rcS.d/S03udev...
[4294679.895000] 9 ms: =s
[4294679.929000] 34 ms: 31 Starting /etc/rcS.d/S04bootup...
[4294679.957000] 26 ms: 10
[4294680.423000] kjournald starting.  Commit interval 5 seconds
[4294680.424000] EXT3 FS on sda1, internal journal
[4294680.424000] EXT3-fs: mounted filesystem with ordered data mode.
[4294680.430000] 473 ms: 12
[4294680.674000] fuse init (API version 7.8)
[4294680.674000] fuse distribution version: 2.7.6
[4294680.913000] usbcore: registered new driver usbserial
[4294680.914000] drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
[4294680.915000] usbcore: registered new driver usbserial_generic
[4294680.916000] drivers/usb/serial/usb-serial.c: USB Serial Driver core
[4294680.942000] drivers/usb/serial/usb-serial.c: USB Serial support registered for FTDI USB Serial Device
[4294680.943000] usbcore: registered new driver ftdi_sio
[4294680.944000] drivers/usb/serial/ftdi_sio.c: v1.4.3:USB FTDI Serial Converters Driver
[4294680.974000] drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303
[4294680.975000] usbcore: registered new driver pl2303
[4294680.976000] drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver
[4294681.038000] 608 ms: 13
[4294681.073000] 35 ms: 14
[4294681.114000] 41 ms: 15
[4294681.152000] 38 ms: 16
[4294681.285000] 133 ms: 17
[4294681.330000] input: dreambox remote control (native) as /class/input/input0
[4294681.331000] input: dreambox advanced remote control (native) as /class/input/input1
[4294681.341000] input: dreambox ir keyboard as /class/input/input2
[4294681.342000] input: dreambox ir mouse as /class/input/input3
[4294683.002000] enter base init, xvd 20100825, vdc 20100719, rap 20100719, xpt 20100825
[4294683.485000] 16:189011000 SMCA: controller reset timed out
[4294683.495000] 16:199007000 SMCB: controller reset timed out
[4294684.250000] register adapter
[4294684.250000] register adapter
[4294684.251000] register adapter
[4294684.252000] register adapter
[4294684.253000] register adapter
[4294684.267000] FP Version 3
[4294684.269000] input: dreambox front panel as /class/input/input4
[4294684.273000] HDMI: no device attached
[4294684.273000] set sb to 3(2)
[4294684.274000] set fb to 2(-1)
[4294684.274000] set input to 0
[4294684.274000] set fb to 2(-1)
[4294684.279000] bcm_video_analog_port_setup (fmt=7)
[4294684.280000] SET FORMAT: display[1], format=7
[4294684.280000] display 0 uses vbi path 1
[4294684.281000] display 1 uses vbi path 0
[4294684.282000] HDMI: hotplug handler!
[4294684.283000] HDMI: no device attached
[4294684.283000] using 50.00Hz as MonitorRefreshRate
[4294684.284000] SET FORMAT: display[0], format=37
[4294684.284000] set fb to 2(0)
[4294684.285000] bcm_video_analog_port_setup (fmt=7)
[4294684.285000] SET FORMAT: display[1], format=7
[4294684.327000] disable wss on display 0
[4294684.327000] disable wss on display 1
[4294684.328000] bcmfb: creating surface with pixel format 0x07e48888 (BPXL_eA8_R8_G8_B8)
[4294684.472000] enable mad
[4294684.527000] VIDEO0: set fallback framerate to 60000
[4294684.527000] VIDEO0: set progressive override mode to 1
[4294684.528000] VIDEO0: set streamtype!
[4294684.528000] set MPEG2
[4294684.529000] sw rave disabled!
[4294684.532000] sync is off so we enable it
[4294684.533000] playback!
[4294684.533000] total video delay: 0 (0 ms)
[4294684.540000] VIDEO0: start decode
[4294684.541000] flush video decoder
[4294684.541000] VIDEO0 got pts failed !!!! (ret 0)
[4294684.996000] set ac3 to downmix
[4294684.997000] set aac to downmix
[4294685.026000] VIDEO0: first pts 0x0
[4294685.049000] init ALSA!
[4294685.051000] DVB: registering new adapter (BCM7405)
[4294685.148000] autodetecting NIMs...
[4294685.149000] ret: 2, feid: 13
[4294685.150000] Found: Slot A, ID: 13 (by CA)
[4294685.150000] Initializing adapter 0 (BCM4505-DVB-S2)
[4294685.177000] enable tsm0
[4294685.212000] bcm4506: found 4505, revision 0(b0)
[4294685.212000] bcm_initAP
[4294685.221000] BCM4506: upload & start firmware
[4294687.112000] bcm4506: ap not running - start now
[4294687.184000] 450X uCode 0x3d
[4294687.229000] no bcm3445 detected
[4294687.242000] DVB: registering adapter 0 frontend 0 (bcm4506)...
[4294687.243000] registered vtuner vtuner0, minor 58
[4294687.244000] registered vtuner vtuner1, minor 57
[4294688.273000] VIDEO0: stop decode
[4294688.273000] no decoder left in sync handling so disable xpt_sync
[4294688.277000] 6992 ms: 18
[4294688.326000] set current avs auto aspect to 16:9
[4294688.326000] disable wss on display 0
[4294688.327000] disable wss on display 1
[4294688.327000] set sb to 3(1)
[4294688.329000] 51 ms: 19
[4294688.359000] 30 ms: 20
[4294688.398000] VIDEO0: set blank to 0
[4294688.399000] 39 ms: 21
[4294688.399000] sync is off so we enable it
[4294688.399000] playback!
[4294688.399000] total video delay: 0 (0 ms)
[4294688.427000] 26 ms: 22
[4294688.456000] VIDEO0: start decode
[4294688.457000] flush video decoder
[4294688.464000] 37 ms: 23
[4294688.509000] 45 ms: 25
[4294688.510000] 1 ms: 26
[4294688.540000] 30 ms: 27
[4294688.645000] VIDEO0: first pts 0x0
[4294688.646000] VIDEO0: framerate changed 3
[4294688.646000] VIDEO0: resolution changed (1280 720)
[4294688.647000] VIDEO0: aspect changed 3
[4294688.648000] set current avs auto aspect to 16:9
[4294688.648000] disable wss on display 0
[4294688.649000] disable wss on display 1
[4294688.649000] set current avs auto aspect to 16:9
[4294688.650000] disable wss on display 0
[4294688.650000] disable wss on display 1
[4294688.651000] set sb to 3(1)
[4294688.764000] VIDEO0: set blank to 0
[4294688.786000] VIDEO0: stop decode
[4294688.787000] VIDEO0: set blank to 0
[4294688.787000] no decoder left in sync handling so disable xpt_sync
[4294693.045000] 4505 ms: 29
[4294694.031000] EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
[4294694.078000] 1032 ms: 30
[4294694.086000] 8 ms: =s
[4294694.379000] 292 ms: 33 Starting /etc/rcS.d/S05dbus-1...
[4294694.388000] 9 ms: =s
[4294694.452000] 64 ms: 35 Starting /etc/rcS.d/S10tpmd...
[4294694.464000] 11 ms: =s
[4294694.722000] usbcore: registered new driver rt73
[4294694.870000] 
[4294694.870000]  _____     ____    _    ____
[4294694.870000] |__  /   _|  _ \  / \  / ___|
[4294694.871000]   / / | | | | | |/ _ \ \___ \
[4294694.872000]  / /| |_| | |_| / ___ \ ___) |
[4294694.872000] /____\__, |____/_/   \_\____/
[4294694.873000]      |___/
[4294694.873000] ZD1211B - version 2.22.0.0-development
[4294694.874000] usbcore: registered new driver zd1211b
[4294694.911000] 447 ms: 37 Starting /etc/rcS.d/S20modutils.sh...
[4294694.920000] 8 ms: =s
[4294695.231000] 311 ms: 39 Starting /etc/rcS.d/S21avahi-daemon...
[4294695.240000] 9 ms: =s
[4294695.405000] 165 ms: 41 Starting /etc/rcS.d/S22avahi-dnsconfd...
[4294695.414000] 9 ms: =s
[4294695.471000] 57 ms: 43 Starting /etc/rcS.d/S38devpts.sh...
[4294695.480000] 8 ms: =s
[4294696.337000] 856 ms: 45 Starting /etc/rcS.d/S40networking...
[4294696.346000] 9 ms: =s
[4294697.131000] 785 ms: 47 Starting /etc/rcS.d/S41rdate...
[4294697.141000] 9 ms: =s
[4294697.201000] 60 ms: 49 Starting /etc/rcS.d/S43portmap...
[4294698.848000] VIDEO0: set blank to 0
[4294698.849000] sync is off so we enable it
[4294698.849000] playback!
[4294698.850000] total video delay: 0 (0 ms)
[4294698.857000] VIDEO0: start decode
[4294698.858000] flush video decoder
[4294698.904000] VIDEO0: first pts 0x0
[4294699.018000] VIDEO0: set blank to 0
[4294699.019000] VIDEO0: stop decode
[4294699.019000] VIDEO0: set blank to 0
[4294699.020000] no decoder left in sync handling so disable xpt_sync
[4294701.937000] bcmfb: enable manual blit
[4294701.957000] bcmfb: creating surface with pixel format 0x07e48888 (BPXL_eA8_R8_G8_B8)
[4294702.375000] bcm4506 channel 0 is in normale mode now
[4294702.996000] 5794 ms: =s
[4294703.027000] 30 ms: 50 
[4294703.230000] 202 ms: 50 
[4294703.281000] 50 ms: 50 
[4294703.318000] 37 ms: 50 
[4294703.912000] 593 ms: 50 
[4294704.237000] 325 ms: 52 
[4294704.667000] 430 ms: 53 
[4294704.826000] 158 ms: 54 
[4294704.837000] 11 ms: 54 
[4294704.839000] 2 ms: 54 
[4294705.336000] 497 ms: 54 
[4294705.364000] 28 ms: 56 
[4294705.378000] bcm4506 channel 0 is sleeping now
[4294705.481000] 116 ms: 56 
[4294705.866000] 385 ms: 56 
[4294708.948000] 3082 ms: 57 
[4294708.994000] 46 ms: 63 
[4294708.996000] 2 ms: 63 
[4294708.998000] 2 ms: 63 
[4294709.016000] 18 ms: 63 
[4294709.038000] 22 ms: 63 
[4294709.189000] 150 ms: 63 
[4294709.217000] 28 ms: 64 
[4294709.230000] 12 ms: 64 
[4294709.256000] 26 ms: 64 
[4294709.286000] 29 ms: 64 
[4294709.330000] 44 ms: 64 
[4294709.332000] 2 ms: 64 
[4294709.335000] 3 ms: 64 
[4294709.343000] 8 ms: 64 
[4294712.172000] 2829 ms: 64 
[4294712.201000] 28 ms: 71 
[4294712.417000] 216 ms: 72 
[4294712.419000] 2 ms: 72 
[4294712.476000] 57 ms: 72 
[4294712.480000] 3 ms: 72 
[4294712.482000] 2 ms: 72 
[4294712.490000] 8 ms: 72 
[4294712.506000] 16 ms: 72 
[4294712.524000] 17 ms: 72 
[4294712.527000] 2 ms: 72 
[4294712.645000] bcmfb: creating surface with pixel format 0x07e48888 (BPXL_eA8_R8_G8_B8)
[4294712.970000] 443 ms: 72 
[4294713.054000] 84 ms: 74 
[4294713.104000] set current avs auto aspect to 4:3
[4294713.105000] disable wss on display 0
[4294713.105000] disable wss on display 1
[4294713.106000] set sb to 3(2)
[4294713.144000] set current avs auto aspect to 4:3
[4294713.145000] disable wss on display 0
[4294713.145000] disable wss on display 1
[4294713.146000] set sb to 3(2)
[4294713.148000] disable wss on display 0
[4294713.148000] set wss 8 on display 1
[4294713.186000] set input to 0
[4294713.186000] set fb to 2(0)
[4294713.187000] set current avs auto aspect to 4:3
[4294713.187000] disable wss on display 0
[4294713.188000] set wss 8 on display 1
[4294713.188000] set sb to 3(2)
[4294713.192000] set ac3 to downmix
[4294713.209000] 155 ms: 74 
[4294713.222000] 13 ms: 74 
[4294713.288000] 66 ms: 74 
[4294713.501000] 213 ms: 74 
[4294713.569000] 67 ms: 75 
[4294713.661000] 91 ms: 75 
[4294714.936000] 1274 ms: 75 
[4294714.969000] 33 ms: 79 
[4294714.977000] 7 ms: 79 
[4294717.504000] set current avs auto aspect to 16:9
[4294717.505000] disable wss on display 0
[4294717.505000] set wss 7 on display 1
[4294717.506000] set sb to 3(1)
[4294717.544000] set current avs auto aspect to 16:9
[4294717.545000] disable wss on display 0
[4294717.545000] set wss 7 on display 1
[4294717.546000] set sb to 3(1)
[4294717.547000] disable wss on display 0
[4294717.548000] set wss 7 on display 1
[4294717.549000] set current avs auto aspect to 16:9
[4294717.550000] disable wss on display 0
[4294717.550000] set wss 7 on display 1
[4294717.551000] set sb to 3(1)
[4294717.555000] set current avs auto aspect to 16:9
[4294717.555000] disable wss on display 0
[4294717.556000] set wss 7 on display 1
[4294717.556000] set sb to 3(1)
[4294717.558000] set current avs auto aspect to 16:9
[4294717.558000] disable wss on display 0
[4294717.559000] set wss 7 on display 1
[4294717.559000] set sb to 3(1)
[4294717.560000] disable wss on display 0
[4294717.561000] set wss 7 on display 1
[4294717.562000] set current avs auto aspect to 16:9
[4294717.563000] disable wss on display 0
[4294717.563000] set wss 7 on display 1
[4294717.564000] set sb to 3(1)
[4294717.568000] set current avs auto aspect to 16:9
[4294717.568000] disable wss on display 0
[4294717.569000] set wss 7 on display 1
[4294717.569000] set sb to 3(1)
[4294717.570000] set current avs auto aspect to 16:9
[4294717.571000] disable wss on display 0
[4294717.572000] set wss 7 on display 1
[4294717.572000] set sb to 3(1)
[4294717.573000] disable wss on display 0
[4294717.573000] set wss 7 on display 1
[4294717.575000] set current avs auto aspect to 16:9
[4294717.575000] disable wss on display 0
[4294717.576000] set wss 7 on display 1
[4294717.576000] set sb to 3(1)
[4294717.580000] set current avs auto aspect to 16:9
[4294717.581000] disable wss on display 0
[4294717.581000] set wss 7 on display 1
[4294717.582000] set sb to 3(1)
[4294717.583000] set current avs auto aspect to 16:9
[4294717.584000] disable wss on display 0
[4294717.584000] set wss 7 on display 1
[4294717.585000] set sb to 3(1)
[4294717.586000] disable wss on display 0
[4294717.586000] set wss 7 on display 1
[4294717.587000] set current avs auto aspect to 16:9
[4294717.588000] disable wss on display 0
[4294717.588000] set wss 7 on display 1
[4294717.589000] set sb to 3(1)
[4294717.593000] set current avs auto aspect to 16:9
[4294717.593000] disable wss on display 0
[4294717.594000] set wss 7 on display 1
[4294717.594000] set sb to 3(1)
[4294717.596000] set current avs auto aspect to 16:9
[4294717.596000] disable wss on display 0
[4294717.597000] set wss 7 on display 1
[4294717.597000] set sb to 3(1)
[4294717.602000] set current avs auto aspect to 16:9
[4294717.603000] disable wss on display 0
[4294717.603000] set wss 7 on display 1
[4294717.604000] set sb to 3(1)
[4294717.605000] set current avs auto aspect to 16:9
[4294717.605000] disable wss on display 0
[4294717.606000] set wss 7 on display 1
[4294717.606000] set sb to 3(1)
[4294717.607000] disable wss on display 0
[4294717.608000] set wss 7 on display 1
[4294717.609000] set current avs auto aspect to 16:9
[4294717.610000] disable wss on display 0
[4294717.610000] set wss 7 on display 1
[4294717.611000] set sb to 3(1)
[4294720.844000] 5866 ms: 79 
[4294721.433000] 589 ms: 94 
[4294722.620000] 1187 ms: 96 
[4294722.697000] set mute 0 (000) 1
[4294722.700000] 80 ms: 99 
[4294722.721000] 21 ms: 99 
[4294723.073000] bcm4506 channel 0 is in normale mode now
[4294724.121000] signal_strength -39.15dbm
[4294724.133000] signal_strength -39.15dbm
[4294724.180000] start pcr0 on dmx 0 pid:b55 index 5
[4294724.183000] start audio on dmx 0 pid:b56
[4294724.183000] audio xpt start
[4294724.184000] sync is off so we enable it
[4294724.184000] demux-index 0 pcr0pid b55
[4294724.185000] using 5 as pcr0 pidchannel
[4294724.185000] MPEG
[4294724.185000] audio: streamtype set 0
[4294724.186000] audio: streamtype_set: stop rave
[4294724.187000] audio: streamtype_set: restart rave
[4294724.188000] set mute 0 (111) 1
[4294724.188000] audio: decoder start 2
[4294724.191000] video delay 0 (0 ms)
[4294724.192000] total video delay: 0 (0 ms)
[4294724.194000] start video0 on dmx 0 pid:b55
[4294724.194000] total video delay: 0 (0 ms)
[4294724.200000] RAP first pts 0x569597a, stc 0x228e26, pcr invalid
[4294724.201000] audio_cdb_itb_error_isr! underflow
[4294724.202000] VIDEO0: start decode
[4294724.204000] audio_cdb_itb_error_isr! underflow
[4294724.209000] audio_cdb_itb_error_isr! underflow
[4294724.213000] audio_cdb_itb_error_isr! underflow
[4294724.217000] audio_cdb_itb_error_isr! underflow
[4294724.221000] audio_cdb_itb_error_isr! underflow
[4294724.222000] ch0: lock
[4294724.223000] RAP sampling rate info isr
[4294724.223000] eModeChange Isr.. set source_changed_event!
[4294724.224000] RAP pts error 0 PTS 0x02b4acbd, STC 0x02b49f24, type 0
[4294724.225000] audio_cdb_itb_error_isr! underflow
[4294724.267000] signal_strength -39.15dbm
[4294724.628000] signal_strength -39.23dbm
[4294724.644000] VIDEO0: first pts 0x569f8a8
[4294724.645000] VIDEO0: resolution changed (720 576)
[4294724.795000] enable tsm0
[4294725.126000] signal_strength -39.19dbm
[4294725.204000] VIDEO0: progressive changed (0)
[4294725.632000] signal_strength -39.09dbm
[4294726.130000] signal_strength -39.26dbm
[4294727.136000] signal_strength -39.17dbm
[4294727.163000] signal_strength -39.17dbm
[4294728.185000] signal_strength -39.17dbm