=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2021.05.13 12:09:24 =~=~=~=~=~=~=~=~=~=~=~= Dreambox DM7 080 M0 M1 SHMOO 0 00000000 1 00000000 C do_boot 3s enter setup 2 1 0 enter setup . . . SL2=1 LLMB=0000C000 BP=02000000 L2Cfg=1E76C637 L2Buf=44707700 BrCfg=F01C204F BrMod=02800001 BrZp0=05000000 BrZp1=00002000 #@ BCM97434B0 CFE v3.15, Endian Mode: Little Build Date: 20140202 (dm@dm) Copyright (C) Broadcom Corporation. MACRONIX SPI flash detected: Size = 16MB, Sector Size 4096, Page Size 256 found card in known state ca valid! CPU speed: 1407MHz DDR Frequency: 667 MHz DDR Mode: DDR3 Total memory(MEMC 0): 1024MB MEMC 0 DDR Width: 32 Total memory(MEMC 1): 1024MB MEMC 1 DDR Width: 32 CFE initialized. *** Autoboot: Trying device 'flash0.kernel' file kernel (flash0.kernel,raw) Loader:elf Filesys:raw Dev:flash0.kernel File:kernel Options: Loading: 0x80001000/18266752 0x8116ca80/280688 Entry address is 0x80580110 Starting program at 0x80580110 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.4-3.0-dm7080 (dora@tigger.dream-property.net) (gcc version 4.8.1 (GCC) ) #15 SMP Sat Sep 13 12:12:38 UTC 2014 [ 0.000000] Fetching vars from bootloader... found 13 vars. [ 0.000000] Options: moca=0 sata=1 pcie=1 usb=1 [ 0.000000] Using 1024 MB + 1024 MB RAM (from CFE) [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00025b00 (Broadcom BMIPS5000) [ 0.000000] FPU revision is: 00130001 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 10000000 @ 00000000 (usable) [ 0.000000] memory: 30000000 @ 20000000 (usable) [ 0.000000] bmem: adding 384 MB RESERVED region at 640 MB (0x18000000@0x28000000) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00050000 [ 0.000000] HighMem empty [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00010000 [ 0.000000] 0: 0x00020000 -> 0x00050000 [ 0.000000] PERCPU: Embedded 7 pages/cpu @819c8000 s6784 r8192 d13696 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259584 [ 0.000000] Kernel command line: bmem=384M@640M memc1=768M console=ttyS0,1000000 root=/dev/mmcblk0p1 rootwait rootfstype=ext4 ip=dhcp [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Primary instruction cache 32kB, physically tagged, 4-way, linesize 64 bytes. [ 0.000000] Primary data cache 32kB, 4-way, linesize 32 bytes. [ 0.000000] MIPS secondary cache 512kB, 8-way, linesize 128 bytes. [ 0.000000] Memory: 628084k/1048576k available (5694k kernel code, 420492k reserved, 1182k data, 10960k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Additional per-CPU info printed with stalls. [ 0.000000] NR_IRQS:160 [ 0.000000] Measuring MIPS counter frequency... [ 0.000000] Detected MIPS clock frequency: 1407 MHz (175.886 MHz counter) [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] Calibrating delay loop... 935.93 BogoMIPS (lpj=467968) [ 0.009000] pid_max: default: 32768 minimum: 301 [ 0.009000] Mount-cache hash table entries: 512 [ 0.010000] Initializing cgroup subsys cpuacct [ 0.010000] Initializing cgroup subsys devices [ 0.011000] Initializing cgroup subsys freezer [ 0.012000] SMP: Booting CPU1... [ 0.012000] CPU revision is: 00025b00 (Broadcom BMIPS5000) [ 0.012000] FPU revision is: 00130001 [ 0.012000] Primary instruction cache 32kB, physically tagged, 4-way, linesize 64 bytes. [ 0.012000] Primary data cache 32kB, 4-way, linesize 32 bytes. [ 0.012000] MIPS secondary cache 512kB, 8-way, linesize 128 bytes. [ 0.022000] SMP: CPU1 is running [ 0.022000] SMP: Booting CPU2... [ 0.022000] CPU revision is: 00025b00 (Broadcom BMIPS5000) [ 0.022000] FPU revision is: 00130001 [ 0.022000] Primary instruction cache 32kB, physically tagged, 4-way, linesize 64 bytes. [ 0.022000] Primary data cache 32kB, 4-way, linesize 32 bytes. [ 0.022000] MIPS secondary cache 512kB, 8-way, linesize 128 bytes. [ 0.031000] SMP: CPU2 is running [ 0.031000] SMP: Booting CPU3... [ 0.031000] CPU revision is: 00025b00 (Broadcom BMIPS5000) [ 0.031000] FPU revision is: 00130001 [ 0.031000] Primary instruction cache 32kB, physically tagged, 4-way, linesize 64 bytes. [ 0.031000] Primary data cache 32kB, 4-way, linesize 32 bytes. [ 0.031000] MIPS secondary cache 512kB, 8-way, linesize 128 bytes. [ 0.040000] SMP: CPU3 is running [ 0.040000] Brought up 4 CPUs [ 0.040000] devtmpfs: initialized [ 0.043000] bmem: adding extra 1024 MB RESERVED region at 2304 MB (0x40000000@0x90000000) [ 0.044000] NET: Registered protocol family 16 [ 0.045000] USB0: power enable is active high; overcurrent is active low [ 0.045000] USB1: power enable is active high; overcurrent is active low [ 0.046000] PCI: PCIe link up, 5.0Gbps x1 [ 0.049000] bio: create slab at 0 [ 0.050000] SCSI subsystem initialized [ 0.051000] usbcore: registered new interface driver usbfs [ 0.051000] usbcore: registered new interface driver hub [ 0.052000] usbcore: registered new device driver usb [ 0.052000] Advanced Linux Sound Architecture Driver Version 1.0.25. [ 0.053000] PCI host bridge to bus 0000:00 [ 0.053000] pci_bus 0000:00: root bus resource [mem 0xd0000000-0xefffffff] [ 0.054000] pci_bus 0000:00: root bus resource [mem 0x00000400-0x000007ff] [ 0.054000] PCI: found device 104c:8241 on PCIe bus, slot 0 (irq 36) [ 0.055000] pci 0000:00:00.0: BAR 0: assigned [mem 0xd0000000-0xd000ffff 64bit] [ 0.056000] pci 0000:00:00.0: BAR 2: assigned [mem 0xd0010000-0xd0011fff 64bit] [ 0.057000] Bluetooth: Core ver 2.16 [ 0.057000] NET: Registered protocol family 31 [ 0.057000] Bluetooth: HCI device and connection manager initialized [ 0.058000] Bluetooth: HCI socket layer initialized [ 0.058000] Bluetooth: L2CAP socket layer initialized [ 0.059000] Bluetooth: SCO socket layer initialized [ 0.059000] cfg80211: Calling CRDA to update world regulatory domain [ 0.060000] Switching to clocksource wktmr [ 0.068000] NET: Registered protocol family 2 [ 0.069000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.070000] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.073000] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.075000] TCP: Hash tables configured (established 131072 bind 65536) [ 0.076000] TCP: reno registered [ 0.077000] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.077000] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.078000] NET: Registered protocol family 1 [ 0.079000] RPC: Registered named UNIX socket transport module. [ 0.080000] RPC: Registered udp transport module. [ 0.080000] RPC: Registered tcp transport module. [ 0.081000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.082000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 0.141000] NFS: Registering the id_resolver key type [ 0.142000] SGI XFS with security attributes, large block/inode numbers, no debug enabled [ 0.143000] msgmni has been set to 1226 [ 0.145000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 0.145000] io scheduler noop registered [ 0.146000] io scheduler cfq registered (default) [ 0.147000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.148000] serial8250.0: ttyS0 at MMIO 0x10406b00 (irq = 67) is a 16550A [ 0.149000] console [ttyS0] enabled, bootconsole disabled [ 0.149000] console [ttyS0] enabled, bootconsole disabled [ 0.151000] loop: module loaded [ 0.151000] ahci: SSS flag set, parallel bus scan disabled [ 0.163000] ahci strict-ahci.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 0.164000] ahci strict-ahci.0: flags: ncq sntf stag clo slum part [ 0.168000] scsi0 : ahci_platform [ 0.169000] scsi1 : ahci_platform [ 0.170000] ata1: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x100 irq 46 [ 0.170000] ata2: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x180 irq 46 [ 0.172000] tun: Universal TUN/TAP device driver, 1.6 [ 0.172000] tun: (C) 1999-2004 Max Krasnyansky [ 0.466000] Found PHY at Address 3 [ 0.466000] bcmgenet: configuring instance #0 for external RGMII [ 0.467000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.468000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI [ 0.468000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1 [ 0.478000] ata1: SATA link down (SStatus 0 SControl 300) [ 0.501000] ehci-brcm ehci-brcm.0: irq 71, io mem 0x10480300 [ 0.507000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00 [ 0.508000] hub 1-0:1.0: USB hub found [ 0.508000] hub 1-0:1.0: 1 port detected [ 0.509000] ehci-brcm ehci-brcm.1: Broadcom STB EHCI [ 0.509000] ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2 [ 0.541000] ehci-brcm ehci-brcm.1: irq 72, io mem 0x10480500 [ 0.547000] ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00 [ 0.547000] hub 2-0:1.0: USB hub found [ 0.548000] hub 2-0:1.0: 1 port detected [ 0.549000] ehci-brcm ehci-brcm.2: Broadcom STB EHCI [ 0.549000] ehci-brcm ehci-brcm.2: new USB bus registered, assigned bus number 3 [ 0.581000] ehci-brcm ehci-brcm.2: irq 76, io mem 0x10490300 [ 0.587000] ehci-brcm ehci-brcm.2: USB 0.0 started, EHCI 1.00 [ 0.587000] hub 3-0:1.0: USB hub found [ 0.588000] hub 3-0:1.0: 1 port detected [ 0.589000] ehci-brcm ehci-brcm.3: Broadcom STB EHCI [ 0.589000] ehci-brcm ehci-brcm.3: new USB bus registered, assigned bus number 4 [ 0.621000] ehci-brcm ehci-brcm.3: irq 77, io mem 0x10490500 [ 0.627000] ehci-brcm ehci-brcm.3: USB 0.0 started, EHCI 1.00 [ 0.627000] hub 4-0:1.0: USB hub found [ 0.628000] hub 4-0:1.0: 1 port detected [ 0.629000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.629000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI [ 0.630000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 5 [ 0.631000] ohci-brcm ohci-brcm.0: irq 73, io mem 0x10480400 [ 0.697000] hub 5-0:1.0: USB hub found [ 0.697000] hub 5-0:1.0: 1 port detected [ 0.698000] ohci-brcm ohci-brcm.1: Broadcom STB OHCI [ 0.699000] ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 6 [ 0.699000] ohci-brcm ohci-brcm.1: irq 74, io mem 0x10480600 [ 0.765000] hub 6-0:1.0: USB hub found [ 0.765000] hub 6-0:1.0: 1 port detected [ 0.766000] ohci-brcm ohci-brcm.2: Broadcom STB OHCI [ 0.767000] ohci-brcm ohci-brcm.2: new USB bus registered, assigned bus number 7 [ 0.767000] ohci-brcm ohci-brcm.2: irq 78, io mem 0x10490400 [ 0.783000] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 0.790000] ata2.00: ATA-7: SAMSUNG HD161GJ, 1AC01118, max UDMA7 [ 0.790000] ata2.00: 312581808 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 0.798000] ata2.00: configured for UDMA/133 [ 0.798000] scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD161GJ 1AC0 PQ: 0 ANSI: 5 [ 0.800000] sd 1:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB) [ 0.801000] sd 1:0:0:0: [sda] Write Protect is off [ 0.801000] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 0.817000] sda: sda1 [ 0.818000] sd 1:0:0:0: [sda] Attached SCSI disk [ 0.833000] hub 7-0:1.0: USB hub found [ 0.833000] hub 7-0:1.0: 1 port detected [ 0.834000] ohci-brcm ohci-brcm.3: Broadcom STB OHCI [ 0.835000] ohci-brcm ohci-brcm.3: new USB bus registered, assigned bus number 8 [ 0.835000] ohci-brcm ohci-brcm.3: irq 79, io mem 0x10490600 [ 0.850000] usb 2-1: new high-speed USB device number 2 using ehci-brcm [ 0.901000] hub 8-0:1.0: USB hub found [ 0.901000] hub 8-0:1.0: 1 port detected [ 0.902000] xhci_hcd 0000:00:00.0: xHCI Host Controller [ 0.903000] xhci_hcd 0000:00:00.0: new USB bus registered, assigned bus number 9 [ 0.904000] xhci switched power on polarity [ 0.905000] hub 9-0:1.0: USB hub found [ 0.905000] hub 9-0:1.0: 2 ports detected [ 0.906000] xhci_hcd 0000:00:00.0: xHCI Host Controller [ 0.906000] xhci_hcd 0000:00:00.0: new USB bus registered, assigned bus number 10 [ 0.907000] hub 10-0:1.0: USB hub found [ 0.908000] hub 10-0:1.0: 2 ports detected [ 0.908000] Initializing USB Mass Storage driver... [ 0.909000] usbcore: registered new interface driver usb-storage [ 0.910000] USB Mass Storage support registered. [ 0.910000] i2c /dev entries driver [ 0.911000] usbcore: registered new interface driver btusb [ 0.912000] sdhci: Secure Digital Host Controller Interface driver [ 0.912000] sdhci: Copyright(c) Pierre Ossman [ 0.913000] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.914000] sdhci-brcmstb sdhci-brcmstb.0: Enabling controller [ 0.919000] mmc0: SDHCI controller on sdhci-brcmstb.0 [sdhci-brcmstb.0] using ADMA [ 0.919000] sdhci-brcmstb sdhci-brcmstb.1: Enabling controller [ 0.925000] mmc1: SDHCI controller on sdhci-brcmstb.1 [sdhci-brcmstb.1] using ADMA [ 0.926000] TCP: cubic registered [ 0.926000] NET: Registered protocol family 10 [ 0.928000] NET: Registered protocol family 17 [ 0.928000] Bluetooth: RFCOMM TTY layer initialized [ 0.929000] Bluetooth: RFCOMM socket layer initialized [ 0.929000] Bluetooth: RFCOMM ver 1.11 [ 0.930000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 0.930000] Bluetooth: BNEP filters: protocol multicast [ 0.931000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 0.932000] L2TP core driver, V2.0 [ 0.932000] Registering the dns_resolver key type [ 0.933000] PM: CP0 COUNT/COMPARE frequency does not depend on divisor [ 0.934000] EBI CS0: setting up SPI flash (primary) [ 0.935000] spi_brcmstb spi_brcmstb.0: master is unqueued, this is deprecated [ 0.936000] spi_brcmstb spi_brcmstb.0: 1-lane output, 3-byte address [ 0.937000] m25p80 spi0.0: mx25l12805d (16384 Kbytes) [ 0.942000] Creating 3 MTD partitions on "spi0.0": [ 0.942000] 0x000000000000-0x000001000000 : "entire_device" [ 0.944000] 0x000000000000-0x000000100000 : "bootloader" [ 0.945000] 0x000000100000-0x000001000000 : "recovery" [ 0.950000] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 0.982000] scsi2 : usb-storage 2-1:1.0 [ 1.026000] mmc0: new high speed MMC card at address 0001 [ 1.027000] mmcblk0: mmc0:0001 SEM04G 3.68 GiB [ 1.028000] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB [ 1.029000] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 1.035000] mmcblk0: p1 p2 [ 1.036000] mmcblk0boot1: unknown partition table [ 1.038000] mmcblk0boot0: unknown partition table [ 1.039000] bcmgenet bcmgenet.0: eth0: link up, 1000 Mbps, full duplex [ 1.041000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 1.052000] Sending DHCP requests ., OK [ 1.065000] IP-Config: Got DHCP answer from 192.168.178.1, my address is 192.168.178.33 [ 1.066000] IP-Config: Complete: [ 1.066000] device=eth0, addr=192.168.178.33, mask=255.255.255.0, gw=192.168.178.1 [ 1.067000] host=192.168.178.33, domain=fritz.box, nis-domain=(none) [ 1.068000] bootserver=192.168.178.1, rootserver=192.168.178.1, rootpath= [ 1.069000] ALSA device list: [ 1.069000] No soundcards found. [ 1.070000] Failed to execute /init INIT: version 2.88 booting Starting udev [ 1.165000] systemd-udevd[92]: starting version 206 [ 1.464000] stb_core: module license 'Proprietary' taints kernel. [ 1.465000] Disabling lock debugging due to kernel taint Starting Bootlog daemon: bootlogd: cannot allocate pseudo tty: No such file or directory bootlogd. rm: can't remove '/tmp': Device or resource busy Configuring network interfaces... ^Cnet.ipv4.conf.default.rp_filter = 1 net.ipv4.conf.all.rp_filter = 1 INIT: Entering runlevel: 5 Starting Dropbear SSH server: Will output 1024 bit rsa secret key to '/etc/dropbear/dropbear_rsa_host_key' Generating key, this may take a while... [ 1.985000] scsi 2:0:0:0: Direct-Access takeMS USB Easy v1.0 PQ: 0 ANSI: 0 CCS [ 2.200000] sd 2:0:0:0: [sdb] 8060928 512-byte logical blocks: (4.12 GB/3.84 GiB) [ 2.202000] sd 2:0:0:0: [sdb] Write Protect is off [ 2.203000] sd 2:0:0:0: [sdb] No Caching mode page found [ 2.203000] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 2.207000] sd 2:0:0:0: [sdb] No Caching mode page found [ 2.208000] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 2.210000] sdb: sdb1 [ 2.213000] sd 2:0:0:0: [sdb] No Caching mode page found [ 2.213000] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 2.214000] sd 2:0:0:0: [sdb] Attached SCSI removable disk Public key portion is: ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAAAgmZkf4lfeUdEqCIaUGHZ4w8YdEs9vED3ijFSYE5uibMG7rtw/kP+32+vTg685i4y5SbBky3DzNIktfK7hwKfwd/FTV/HLTuPu9bzz3P8S4wyMBb+4l2Z94Tueb9YHicS8M1OgnRp/cZIi75l2cAiF7LaPh53GsgcfbrdftPUtQX3B/U= root@dm7080 Fingerprint: md5 c4:d4:97:e1:09:35:93:a6:2e:47:32:fa:98:0b:41:e8 dropbear. Starting recovery-ui. Starting internet superserver: xinetd. Starting Lighttpd Web Server: lighttpd. 1970-01-01 00:00:02: (log.c.164) server started Stopping Bootlog daemon: bootlogd. opendreambox 2.2.0 dm7080 /dev/ttyS0 >>> Your Dreambox has booted into RESCUE MODE. >>> Please log in as user 'root' (no password required), >>> then run 'help' to get further information. dm7080 login: root login[268]: root login on 'ttyS0' root@dm7080:~# ifconfig eth0 -auto ifconfig: bad address '-auto' root@dm7080:~# [ 111.643000] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 111.856000] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 122.372000] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 123.456000] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)  Broadcast message from root@dm7080 (Thu Jan 1 00:03:06 1970): The system is going down for reboot NOW! INIT: Switching to runlevel: 6 INIT: Sending processes the TERM signal INIT: Sending processes the KILL sigStopping Dropbear SSH server: no /bin/true found; none killed Stopping recovery-ui. Stopping internet superserver: xinetd. Unmounting remote filesystems... Deconfiguring network interfaces... ifdown: interface lo not configured ifdown: interface eth0 not configured done. Stopping Lighttpd Web Server: stopped /usr/sbin/lighttpd (pid 263) lighttpd. Sending all processes the TERM signal... Sending all processes the KILL signal... Deactivating swap... Unmounting local filesystems... Rebooting... [ 199.959000] sd 1:0:0:0: [sda] Synchronizing SCSI cache [ 199.963000] Restarting system. Dreambox DM7 080 M0 M1 SHMOO 0 00000000 1 00000000 C do_boot 3s enter setup 2 1 0 enter setup . . . SL2=1 LLMB=0000C000 BP=02000000 L2Cfg=1E76C637 L2Buf=44707700 BrCfg=F01C204F BrMod=02800001 BrZp0=05000000 BrZp1=00002000 #@ BCM97434B0 CFE v3.15, Endian Mode: Little Build Date: 20140202 (dm@dm) Copyright (C) Broadcom Corporation. MACRONIX SPI flash detected: Size = 16MB, Sector Size 4096, Page Size 256 found card in known state ca valid! CPU speed: 1407MHz DDR Frequency: 667 MHz DDR Mode: DDR3 Total memory(MEMC 0): 1024MB MEMC 0 DDR Width: 32 Total memory(MEMC 1): 1024MB MEMC 1 DDR Width: 32 CFE initialized. *** Autoboot: Trying device 'flash0.kernel' file kernel (flash0.kernel,raw) Loader:elf Filesys:raw Dev:flash0.kernel File:kernel Options: Loading: 0x80001000/18266752 0x8116ca80/280688 Entry address is 0x80580110 Starting program at 0x80580110 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.4-3.0-dm7080 (dora@tigger.dream-property.net) (gcc version 4.8.1 (GCC) ) #15 SMP Sat Sep 13 12:12:38 UTC 2014 [ 0.000000] Fetching vars from bootloader... found 13 vars. [ 0.000000] Options: moca=0 sata=1 pcie=1 usb=1 [ 0.000000] Using 1024 MB + 1024 MB RAM (from CFE) [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00025b00 (Broadcom BMIPS5000) [ 0.000000] FPU revision is: 00130001 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 10000000 @ 00000000 (usable) [ 0.000000] memory: 30000000 @ 20000000 (usable) [ 0.000000] bmem: adding 384 MB RESERVED region at 640 MB (0x18000000@0x28000000) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00050000 [ 0.000000] HighMem empty [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00010000 [ 0.000000] 0: 0x00020000 -> 0x00050000 [ 0.000000] PERCPU: Embedded 7 pages/cpu @819c8000 s6784 r8192 d13696 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259584 [ 0.000000] Kernel command line: bmem=384M@640M memc1=768M console=ttyS0,1000000 root=/dev/mmcblk0p1 rootwait rootfstype=ext4 ip=dhcp [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Primary instruction cache 32kB, physically tagged, 4-way, linesize 64 bytes. [ 0.000000] Primary data cache 32kB, 4-way, linesize 32 bytes. [ 0.000000] MIPS secondary cache 512kB, 8-way, linesize 128 bytes. [ 0.000000] Memory: 628084k/1048576k available (5694k kernel code, 420492k reserved, 1182k data, 10960k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Additional per-CPU info printed with stalls. [ 0.000000] NR_IRQS:160 [ 0.000000] Measuring MIPS counter frequency... [ 0.000000] Detected MIPS clock frequency: 1407 MHz (175.886 MHz counter) [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] Calibrating delay loop... 935.93 BogoMIPS (lpj=467968) [ 0.009000] pid_max: default: 32768 minimum: 301 [ 0.009000] Mount-cache hash table entries: 512 [ 0.010000] Initializing cgroup subsys cpuacct [ 0.010000] Initializing cgroup subsys devices [ 0.011000] Initializing cgroup subsys freezer [ 0.012000] SMP: Booting CPU1... [ 0.012000] CPU revision is: 00025b00 (Broadcom BMIPS5000) [ 0.012000] FPU revision is: 00130001 [ 0.012000] Primary instruction cache 32kB, physically tagged, 4-way, linesize 64 bytes. [ 0.012000] Primary data cache 32kB, 4-way, linesize 32 bytes. [ 0.012000] MIPS secondary cache 512kB, 8-way, linesize 128 bytes. [ 0.022000] SMP: CPU1 is running [ 0.022000] SMP: Booting CPU2... [ 0.022000] CPU revision is: 00025b00 (Broadcom BMIPS5000) [ 0.022000] FPU revision is: 00130001 [ 0.022000] Primary instruction cache 32kB, physically tagged, 4-way, linesize 64 bytes. [ 0.022000] Primary data cache 32kB, 4-way, linesize 32 bytes. [ 0.022000] MIPS secondary cache 512kB, 8-way, linesize 128 bytes. [ 0.031000] SMP: CPU2 is running [ 0.031000] SMP: Booting CPU3... [ 0.031000] CPU revision is: 00025b00 (Broadcom BMIPS5000) [ 0.031000] FPU revision is: 00130001 [ 0.031000] Primary instruction cache 32kB, physically tagged, 4-way, linesize 64 bytes. [ 0.031000] Primary data cache 32kB, 4-way, linesize 32 bytes. [ 0.031000] MIPS secondary cache 512kB, 8-way, linesize 128 bytes. [ 0.040000] SMP: CPU3 is running [ 0.040000] Brought up 4 CPUs [ 0.040000] devtmpfs: initialized [ 0.043000] bmem: adding extra 1024 MB RESERVED region at 2304 MB (0x40000000@0x90000000) [ 0.044000] NET: Registered protocol family 16 [ 0.045000] USB0: power enable is active high; overcurrent is active low [ 0.045000] USB1: power enable is active high; overcurrent is active low [ 0.046000] PCI: PCIe link up, 5.0Gbps x1 [ 0.049000] bio: create slab at 0 [ 0.050000] SCSI subsystem initialized [ 0.051000] usbcore: registered new interface driver usbfs [ 0.051000] usbcore: registered new interface driver hub [ 0.052000] usbcore: registered new device driver usb [ 0.052000] Advanced Linux Sound Architecture Driver Version 1.0.25. [ 0.053000] PCI host bridge to bus 0000:00 [ 0.053000] pci_bus 0000:00: root bus resource [mem 0xd0000000-0xefffffff] [ 0.054000] pci_bus 0000:00: root bus resource [mem 0x00000400-0x000007ff] [ 0.054000] PCI: found device 104c:8241 on PCIe bus, slot 0 (irq 36) [ 0.055000] pci 0000:00:00.0: BAR 0: assigned [mem 0xd0000000-0xd000ffff 64bit] [ 0.056000] pci 0000:00:00.0: BAR 2: assigned [mem 0xd0010000-0xd0011fff 64bit] [ 0.057000] Bluetooth: Core ver 2.16 [ 0.057000] NET: Registered protocol family 31 [ 0.057000] Bluetooth: HCI device and connection manager initialized [ 0.058000] Bluetooth: HCI socket layer initialized [ 0.058000] Bluetooth: L2CAP socket layer initialized [ 0.059000] Bluetooth: SCO socket layer initialized [ 0.059000] cfg80211: Calling CRDA to update world regulatory domain [ 0.060000] Switching to clocksource wktmr [ 0.068000] NET: Registered protocol family 2 [ 0.069000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.070000] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.073000] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.075000] TCP: Hash tables configured (established 131072 bind 65536) [ 0.076000] TCP: reno registered [ 0.077000] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.077000] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.078000] NET: Registered protocol family 1 [ 0.079000] RPC: Registered named UNIX socket transport module. [ 0.080000] RPC: Registered udp transport module. [ 0.080000] RPC: Registered tcp transport module. [ 0.081000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.082000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 0.141000] NFS: Registering the id_resolver key type [ 0.142000] SGI XFS with security attributes, large block/inode numbers, no debug enabled [ 0.143000] msgmni has been set to 1226 [ 0.145000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 0.146000] io scheduler noop registered [ 0.146000] io scheduler cfq registered (default) [ 0.147000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.148000] serial8250.0: ttyS0 at MMIO 0x10406b00 (irq = 67) is a 16550A [ 0.149000] console [ttyS0] enabled, bootconsole disabled [ 0.149000] console [ttyS0] enabled, bootconsole disabled [ 0.151000] loop: module loaded [ 0.151000] ahci: SSS flag set, parallel bus scan disabled [ 0.163000] ahci strict-ahci.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 0.164000] ahci strict-ahci.0: flags: ncq sntf stag clo slum part [ 0.168000] scsi0 : ahci_platform [ 0.169000] scsi1 : ahci_platform [ 0.170000] ata1: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x100 irq 46 [ 0.170000] ata2: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x180 irq 46 [ 0.172000] tun: Universal TUN/TAP device driver, 1.6 [ 0.172000] tun: (C) 1999-2004 Max Krasnyansky [ 0.466000] Found PHY at Address 3 [ 0.466000] bcmgenet: configuring instance #0 for external RGMII [ 0.467000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.468000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI [ 0.468000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1 [ 0.477000] ata1: SATA link down (SStatus 0 SControl 300) [ 0.501000] ehci-brcm ehci-brcm.0: irq 71, io mem 0x10480300 [ 0.507000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00 [ 0.508000] hub 1-0:1.0: USB hub found [ 0.508000] hub 1-0:1.0: 1 port detected [ 0.509000] ehci-brcm ehci-brcm.1: Broadcom STB EHCI [ 0.509000] ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2 [ 0.541000] ehci-brcm ehci-brcm.1: irq 72, io mem 0x10480500 [ 0.547000] ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00 [ 0.547000] hub 2-0:1.0: USB hub found [ 0.548000] hub 2-0:1.0: 1 port detected [ 0.549000] ehci-brcm ehci-brcm.2: Broadcom STB EHCI [ 0.549000] ehci-brcm ehci-brcm.2: new USB bus registered, assigned bus number 3 [ 0.581000] ehci-brcm ehci-brcm.2: irq 76, io mem 0x10490300 [ 0.587000] ehci-brcm ehci-brcm.2: USB 0.0 started, EHCI 1.00 [ 0.587000] hub 3-0:1.0: USB hub found [ 0.588000] hub 3-0:1.0: 1 port detected [ 0.589000] ehci-brcm ehci-brcm.3: Broadcom STB EHCI [ 0.589000] ehci-brcm ehci-brcm.3: new USB bus registered, assigned bus number 4 [ 0.621000] ehci-brcm ehci-brcm.3: irq 77, io mem 0x10490500 [ 0.627000] ehci-brcm ehci-brcm.3: USB 0.0 started, EHCI 1.00 [ 0.627000] hub 4-0:1.0: USB hub found [ 0.628000] hub 4-0:1.0: 1 port detected [ 0.629000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.629000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI [ 0.630000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 5 [ 0.631000] ohci-brcm ohci-brcm.0: irq 73, io mem 0x10480400 [ 0.697000] hub 5-0:1.0: USB hub found [ 0.697000] hub 5-0:1.0: 1 port detected [ 0.698000] ohci-brcm ohci-brcm.1: Broadcom STB OHCI [ 0.699000] ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 6 [ 0.699000] ohci-brcm ohci-brcm.1: irq 74, io mem 0x10480600 [ 0.765000] hub 6-0:1.0: USB hub found [ 0.765000] hub 6-0:1.0: 1 port detected [ 0.766000] ohci-brcm ohci-brcm.2: Broadcom STB OHCI [ 0.767000] ohci-brcm ohci-brcm.2: new USB bus registered, assigned bus number 7 [ 0.767000] ohci-brcm ohci-brcm.2: irq 78, io mem 0x10490400 [ 0.782000] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 0.789000] ata2.00: ATA-7: SAMSUNG HD161GJ, 1AC01118, max UDMA7 [ 0.789000] ata2.00: 312581808 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 0.797000] ata2.00: configured for UDMA/133 [ 0.797000] scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD161GJ 1AC0 PQ: 0 ANSI: 5 [ 0.799000] sd 1:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB) [ 0.800000] sd 1:0:0:0: [sda] Write Protect is off [ 0.800000] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 0.811000] sda: sda1 [ 0.812000] sd 1:0:0:0: [sda] Attached SCSI disk [ 0.833000] hub 7-0:1.0: USB hub found [ 0.833000] hub 7-0:1.0: 1 port detected [ 0.834000] ohci-brcm ohci-brcm.3: Broadcom STB OHCI [ 0.835000] ohci-brcm ohci-brcm.3: new USB bus registered, assigned bus number 8 [ 0.835000] ohci-brcm ohci-brcm.3: irq 79, io mem 0x10490600 [ 0.850000] usb 2-1: new high-speed USB device number 2 using ehci-brcm [ 0.901000] hub 8-0:1.0: USB hub found [ 0.901000] hub 8-0:1.0: 1 port detected [ 0.902000] xhci_hcd 0000:00:00.0: xHCI Host Controller [ 0.903000] xhci_hcd 0000:00:00.0: new USB bus registered, assigned bus number 9 [ 0.904000] xhci switched power on polarity [ 0.905000] hub 9-0:1.0: USB hub found [ 0.905000] hub 9-0:1.0: 2 ports detected [ 0.906000] xhci_hcd 0000:00:00.0: xHCI Host Controller [ 0.906000] xhci_hcd 0000:00:00.0: new USB bus registered, assigned bus number 10 [ 0.907000] hub 10-0:1.0: USB hub found [ 0.908000] hub 10-0:1.0: 2 ports detected [ 0.908000] Initializing USB Mass Storage driver... [ 0.909000] usbcore: registered new interface driver usb-storage [ 0.910000] USB Mass Storage support registered. [ 0.910000] i2c /dev entries driver [ 0.911000] usbcore: registered new interface driver btusb [ 0.912000] sdhci: Secure Digital Host Controller Interface driver [ 0.912000] sdhci: Copyright(c) Pierre Ossman [ 0.913000] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.913000] sdhci-brcmstb sdhci-brcmstb.0: Enabling controller [ 0.919000] mmc0: SDHCI controller on sdhci-brcmstb.0 [sdhci-brcmstb.0] using ADMA [ 0.919000] sdhci-brcmstb sdhci-brcmstb.1: Enabling controller [ 0.925000] mmc1: SDHCI controller on sdhci-brcmstb.1 [sdhci-brcmstb.1] using ADMA [ 0.926000] TCP: cubic registered [ 0.926000] NET: Registered protocol family 10 [ 0.928000] NET: Registered protocol family 17 [ 0.928000] Bluetooth: RFCOMM TTY layer initialized [ 0.929000] Bluetooth: RFCOMM socket layer initialized [ 0.929000] Bluetooth: RFCOMM ver 1.11 [ 0.930000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 0.930000] Bluetooth: BNEP filters: protocol multicast [ 0.931000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 0.932000] L2TP core driver, V2.0 [ 0.932000] Registering the dns_resolver key type [ 0.933000] PM: CP0 COUNT/COMPARE frequency does not depend on divisor [ 0.934000] EBI CS0: setting up SPI flash (primary) [ 0.935000] spi_brcmstb spi_brcmstb.0: master is unqueued, this is deprecated [ 0.936000] spi_brcmstb spi_brcmstb.0: 1-lane output, 3-byte address [ 0.937000] m25p80 spi0.0: mx25l12805d (16384 Kbytes) [ 0.942000] Creating 3 MTD partitions on "spi0.0": [ 0.943000] 0x000000000000-0x000001000000 : "entire_device" [ 0.944000] 0x000000000000-0x000000100000 : "bootloader" [ 0.945000] 0x000000100000-0x000001000000 : "recovery" [ 0.948000] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 0.983000] scsi2 : usb-storage 2-1:1.0 [ 1.027000] mmc0: new high speed MMC card at address 0001 [ 1.028000] mmcblk0: mmc0:0001 SEM04G 3.68 GiB [ 1.029000] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB [ 1.030000] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 1.036000] mmcblk0: p1 p2 [ 1.037000] mmcblk0boot1: unknown partition table [ 1.038000] mmcblk0boot0: unknown partition table [ 1.987000] scsi 2:0:0:0: Direct-Access takeMS USB Easy v1.0 PQ: 0 ANSI: 0 CCS [ 2.203000] sd 2:0:0:0: [sdb] 8060928 512-byte logical blocks: (4.12 GB/3.84 GiB) [ 2.204000] sd 2:0:0:0: [sdb] Write Protect is off [ 2.205000] sd 2:0:0:0: [sdb] No Caching mode page found [ 2.206000] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 2.209000] sd 2:0:0:0: [sdb] No Caching mode page found [ 2.210000] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 2.212000] sdb: sdb1 [ 2.214000] sd 2:0:0:0: [sdb] No Caching mode page found [ 2.215000] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 2.215000] sd 2:0:0:0: [sdb] Attached SCSI removable disk [ 3.042000] bcmgenet bcmgenet.0: eth0: link up, 1000 Mbps, full duplex [ 3.044000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 3.055000] Sending DHCP requests .., OK [ 5.919000] IP-Config: Got DHCP answer from 192.168.178.1, my address is 192.168.178.33 [ 5.920000] IP-Config: Complete: [ 5.920000] device=eth0, addr=192.168.178.33, mask=255.255.255.0, gw=192.168.178.1 [ 5.921000] host=192.168.178.33, domain=fritz.box, nis-domain=(none) [ 5.922000] bootserver=192.168.178.1, rootserver=192.168.178.1, rootpath= [ 5.923000] ALSA device list: [ 5.923000] No soundcards found. [ 5.924000] Failed to execute /init INIT: version 2.88 booting Starting udev [ 5.998000] systemd-udevd[93]: starting version 206 [ 6.432000] stb_core: module license 'Proprietary' taints kernel. [ 6.433000] Disabling lock debugging due to kernel taint Starting Bootlog daemon: bootlogd: cannot allocate pseudo tty: No such file or directory bootlogd. rm: can't remove '/tmp': Device or resource busy Configuring network interfaces... udhcpc (v1.21.1) started Sending discover... Sending select for 192.168.178.33... Lease of 192.168.178.33 obtained, lease time 86400 /etc/udhcpc.d/50default: Adding DNS 192.168.178.1 done. net.ipv4.conf.default.rp_filter = 1 net.ipv4.conf.all.rp_filter = 1 INIT: Entering runlevel: 5 Starting Dropbear SSH server: Will output 1024 bit rsa secret key to '/etc/dropbear/dropbear_rsa_host_key' Generating key, this may take a while... Public key portion is: ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAAAgwCFS9xmYk7USeqERAlkJnLU+24huD2TxFb+kEv9CoCk+kP7SoZiRc/gOySEJPfifXWVSiBU9KsY1WHyVniqA88IfaY8JnmUJuZcGGvxVSBvXB5K2e2wQT6nmmwqXcdBc6vfSaLJWRvi7NfUdwPbiNVB2Cxw36Wk8hFNcSCoJ/NQMkZ7 root@dm7080 Fingerprint: md5 21:a5:dd:3e:01:68:72:c2:94:8e:0c:cb:79:cd:96:8b dropbear. Starting recovery-ui. Starting internet superserver: xinetd. Starting Lighttpd Web Server: lighttpd. 1970-01-01 00:00:07: (log.c.164) server started Stopping Bootlog daemon: bootlogd. opendreambox 2.2.0 dm7080 /dev/ttyS0 >>> Your Dreambox has booted into RESCUE MODE. >>> Please log in as user 'root' (no password required), >>> then run 'help' to get further information. dm7080 login: