Parted Magic 2015_09_29 (hdparm v9.48) Secure Erase Log Started: Thu Mar 14 19:13:27 CDT 2024 Finished: Fri Mar 15 00:36:49 CDT 2024 ST2000LM015-2E81 (/dev/sda) SERIAL NUMBER: WDZSS90Q SIZE: 1.8T RESULTS:Successfully Erased Secure Erase Method: Enhanced Secure Erase ================================================== ST2000LM015-2E81 (/dev/sda) ================================================== hdparm v9.48 /dev/sda: ATA device, with non-removable media Model Number: ST2000LM015-2E8174 Serial Number: WDZSS90Q Firmware Revision: 0001 Transport: Serial, ATA8-AST, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6, SATA Rev 3.0 Standards: Used: unknown (minor revision code 0x001f) Supported: 10 9 8 7 6 5 Likely used: 10 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 3907029168 Logical Sector size: 512 bytes Physical Sector size: 4096 bytes Logical Sector-0 offset: 0 bytes device size with M = 1024*1024: 1907729 MBytes device size with M = 1000*1000: 2000398 MBytes (2000 GB) cache/buffer size = unknown Form Factor: 2.5 inch Nominal Media Rotation Rate: 5400 Capabilities: LBA, IORDY(can be disabled) Queue depth: 32 Standby timer values: spec'd by Standard, no device specific minimum R/W multiple sector transfer: Max = 16 Current = 16 Advanced power management level: 128 Recommended acoustic management value: 208, current value: 208 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * SMART feature set Security Mode feature set * Power Management feature set * Write cache * Look-ahead * Host Protected Area feature set * WRITE_BUFFER command * READ_BUFFER command * NOP cmd * DOWNLOAD_MICROCODE * Advanced Power Management feature set Power-Up In Standby feature set * SET_FEATURES required to spinup after power up SET_MAX security extension * 48-bit Address feature set * Device Configuration Overlay feature set * Mandatory FLUSH_CACHE * FLUSH_CACHE_EXT * SMART error logging * SMART self-test * General Purpose Logging feature set * WRITE_{DMA|MULTIPLE}_FUA_EXT * 64-bit World wide name * IDLE_IMMEDIATE with UNLOAD Write-Read-Verify feature set * WRITE_UNCORRECTABLE_EXT command * {READ,WRITE}_DMA_EXT_GPL commands * Segmented DOWNLOAD_MICROCODE * Gen1 signaling speed (1.5Gb/s) * Gen2 signaling speed (3.0Gb/s) * Gen3 signaling speed (6.0Gb/s) * Native Command Queueing (NCQ) * Host-initiated interface power management * Phy event counters * Idle-Unload when NCQ is active * READ_LOG_DMA_EXT equivalent to READ_LOG_EXT * DMA Setup Auto-Activate optimization Device-initiated interface power management Asynchronous notification (eg. media change) * Software settings preservation * SMART Command Transport (SCT) feature set * SCT Write Same (AC2) * SCT Features Control (AC4) * SCT Data Tables (AC5) unknown 206[12] (vendor specific) unknown 206[13] (vendor specific) * DOWNLOAD MICROCODE DMA command * Data Set Management TRIM supported (limit 8 blocks) Security: Master password revision code = 65534 supported not enabled not locked not frozen not expired: security count supported: enhanced erase 332min for SECURITY ERASE UNIT. 332min for ENHANCED SECURITY ERASE UNIT. Logical Unit WWN Device Identifier: 5000c500d4d50e5e NAA : 5 IEEE OUI : 000c50 Unique ID : 0d4d50e5e Checksum: correct smartctl 6.4 2015-06-04 r4109 [x86_64-linux-4.1.7-pmagic64] (local build) Copyright (C) 2002-15, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: ST2000LM015-2E8174 Serial Number: WDZSS90Q LU WWN Device Id: 5 000c50 0d4d50e5e Firmware Version: 0001 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Mar 15 00:36:49 2024 CDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x71) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 331) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 078 039 006 Pre-fail Always - 63656872 3 Spin_Up_Time 0x0003 100 099 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 994 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 074 060 045 Pre-fail Always - 22614562 9 Power_On_Hours 0x0032 096 096 000 Old_age Always - 4070 (217 43 0) 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 90 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 061 048 040 Old_age Always - 39 (Min/Max 28/39) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 11 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 185 193 Load_Cycle_Count 0x0032 099 099 000 Old_age Always - 3980 194 Temperature_Celsius 0x0022 039 052 000 Old_age Always - 39 (0 17 0 0 0) 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 1627 (234 215 0) 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 16498915072 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 411474347 254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 1 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 occurred at disk power-on lifetime: 4010 hours (167 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 71 00 00 00 00 e0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ea 00 00 00 00 00 a0 00 3d+09:38:03.326 FLUSH CACHE EXT 61 00 30 ff ff ff 4f 00 3d+09:38:03.324 WRITE FPDMA QUEUED 61 00 78 a8 11 eb 4e 00 3d+09:38:03.324 WRITE FPDMA QUEUED 61 00 78 30 10 eb 4e 00 3d+09:38:03.024 WRITE FPDMA QUEUED 61 00 78 b8 0e eb 4e 00 3d+09:38:02.827 WRITE FPDMA QUEUED SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 4065 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.