CPU 01<\r> <\n>Dreambox DM9<\0>20<\r> <\r> <\n>AVS init...<\r> <\n>AVS init OK<\r> <\n>AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a002b00<\r> <\n>AVS load_code offset =00051000<\r> <\n>LOADED<\r> <\n>AVS: overtemp mon ON<\r> <\n><\r> <\n>single board<\r> <\n>select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2500<\r> <\n>MEMSYS-STD<\r> <\n>SHMOO 02010000 BLD:11138M HW:hpf0_b1p6 V:2.1.0.0<\r> <\n>MCB: FLEX<\r> <\n>AVS start:NO<\r> <\n>DDR0: !@ ffe0e780 <= ffe0df10 MEMSYS-0 @ f1100000 OK<\r> <\n>DDR1: =@ ffe0e780 <= ffe0df10 MEMSYS-1 @ f1180000 OK<\r> <\n>Sdram Scramble OTP = 0x00000001 <\r> <\n>Sdram Scramble OK<\r> <\n>select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 1b25252b<\r> <\n>BFW load mode OTP = 0x0000000f <\r> <\n>bfw_hash_locked = 0x00000000 <\r> <\n>BFW key3 OK, BFW load OK<\r> <\n>BFW v2.1.0<\r> <\n>COPY CODE... DONE<\r> <\n>MICH: disable success<\r> <\n>SSBL<\r> <\n>PINMUX<\r> <\n>CACHE FLUSH OK<\r> <\n>MMU ON<\r> <\n>CACHE FLUSH OK<\r> <\n>_fbss 07081d40<\r> <\n>_ebss 0713ede0<\r> <\n>_end 0713ee00<\r> <\n>HEAP @ 07200000<\r> <\n>STACK @ 09300000<\r> <\n>ARCH: CONFIG OK<\r> <\n>CLR BSS 07081d40 to 0713ede0 OK<\r> <\n>CLR SRAM OK<\r> <\n>CACHE FLUSH OK<\r> <\n>CPU CLKSET OK<\r> <\n>GO!<\r> <\n><\r> <\n><27>[33;1m ,/ <27>[0m <\r> <\n><27>[33;1m ,'/___,<27>[0m BOLT v1.18 v1.18 LOCAL BUILD<\r> <\n><27>[33;1m.'__ ,' <27>[0m (2021-08-31 12:00:08 cynric@cynric-VirtualBox)<\r> <\n><27>[33;1m /,' <27>[0m Copyright (C) 2021 Broadcom<\r> <\n><27>[33;1m /' <27>[0m <\r> <\n><27>[0m<\r> <\n>Board: BCM97252SSFF<\r> <\n>SYS_CTRL: product=72521, family=7439b2, strap=000000b2, <\r> <\n>otp @ 0xf0404030 = 0x822000e0: en_cr(0x00000060) en_testport(0x00000080) macrovision_disable(0x02000000) moca_disable(0x80000000) rv9_disable(0x00200000) <\r> <\n>otp @ 0xf0404034 = 0x00000021: moca2_disable(0x00000001) rfm_disable(0x00000020) <\r> <\n>CPU: 2x B15 [420f00f3] 1719 MHz<\r> <\n>SCB: 432 MHz<\r> <\n>DDR0 @ 1067MHz, DDR1 @ 1067MHz<\r> <\n>RESET CAUSE: 0x000001 power_on (1 of 23 possible causes)<\r> <\n>CS0: SFDP SPI, 32MB, 64kB blocks, 64kB erase block, 256B pages<\r> <\n><27>[31;1mCS1: NAND: unrecognized ID: 0x7fff 0xffffffff<27>[0m<\r> <\n>RTS0: 0x1101004, 256 clients, ok<\r> <\n>RTS1: 0x1181004, 256 clients, ok<\r> <\n>BOX MODE: 5<\r> <\n>card if inited<\r> <\n>set pwm to 0/255<\r> <\n>disp id ffff<\r> <\n>load image<\r> <\n>AVS: park check<\r> <\n>AVS: temperature monitoring enabled<\r> <\n>AVS: V=0.987V, T=+47.225C (no AVS FW)<\r> <\n>USB otp=00000040<\r> <\n>USB @ 0xf0470200: IPP is active low, IOC is negative polarity<\r> <\n>init fp<\r> <\n>ATR length 0b. TPM version -1<\r> <\n>ATR invalid!<\r> <\n>found card in unknown state<\r> <\n>error in receive<\r> <\n>error during t1 transfer<\r> <\n>cannot read fabca-cert<\r> <\n>retrying.. card if inited<\r> <\n>ATR length 18b. TPM version 3<\r> <\n>found card in unknown state<\r> <\n>ca valid!<\r> <\n>set pwm to 200/255<\r> <\n><27>[34;1mNormal bootup<27>[0m<\r> <\n>Loader:zimg Filesys:raw Dev:emmcflash0.kernel File: Options:(null)<\r> <\n>Reading 4249144 bytes from zImage...........<\r> <\n>Starting program at 0x8000 (DTB @ 0x7728000)<\r> <\n><\r> <\n>32 bit boot...<\r> <\n>Uncompressing Linux... done, booting the kernel.<\r> <\n>