=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2010.05.19 18:58:00 =~=~=~=~=~=~=~=~=~=~=~= BCM97400 AB FFFFFFFF 1s Sync=0 LLMB=0 L2=0 RAC_I=0 RAC_D=0 Copy Code...34TUCV (c) 2007,2008 Dream Multimedia GmbH. All rights reserved. Dreambox DM8000 FIRST STAGE 1.00 {BO23456}  2ND STAGE OK, build #76 (20091014) 0.000 - BCM board setup Configure MEMC1_2........ Done 0.039 - fp init FP version 7 detected 0.106 - ca init 0.820 - load config 1.400 - config loaded. * press [S] to enter setup OLED found! BOOT #76(20091014) - NAND PROBE: 2c da 80 15 (normal) detected jffs2 blocksize: 128kb ++++++++++++++++++++++++ dreamupd initialized Scanning JFFS2 FS: . | / - \ | / - \ | / -  done. /flash/bootlogo.elf bootlogo size: 54721 *** BHDM_EDID: One Bit Audio - **** NOT Implemented/Supported by BCM7400 ; [4D 02 00] *** BHDM_EDID: DTS-HD - **** NOT Implemented/Supported by BCM7400 ; [5F 7E 01] *** BHDM_EDID: MAT (MLP) - **** NOT Implemented/Supported by BCM7400 ; [67 54 00] Available modes: 720x480i_59.94Hz 720x480i_59.94Hz 720x480i_59.94Hz 720x576i_50.00Hz 720x576i_50.00Hz 720x576i_50.00Hz 720x576i_50.00Hz 720x576i_50.00Hz 720x576i_50.00Hz 720x576i_50.00Hz 720x576i_50.00Hz 720x480i_60.00Hz 720x576i_50.00Hz 720x576i_50.00Hz 720x480i_60.00Hz 720x576i_50.00Hz 720x576i_50.00Hz 720x576i_50.00Hz 720x576i_50.00Hz 720x576i_50.00Hz 720x576i_50.00Hz 1920x1080i_60.00Hz 1280x720p_60.00Hz 720x480p_59.94Hz 1920x1080i_50.00Hz 1920x1080i_50.00Hz 1280x720p_50.00Hz 720x576p_50.00Hz 640x480p_60.00Hz 800x600p_60.00Hz 1024x768p_60.00Hz 1280x720p_50.00Hz 1280x720p_60.00Hz 1280x720p_60.00Hz 640x480p_70.00Hz 640x480p_72.81Hz 640x480p_75.00Hz 640x480p_85.00Hz 1024x768p_70.00Hz 1024x768p_72.00Hz 1024x768p_75.00Hz 1024x768p_85.00Hz 1280x720p_70.00Hz 1280x720p_72.00Hz 1280x720p_75.00Hz 1280x720p_85.00Hz 720x480i_60.00Hz using 1920x1080i (50.00 Hz) HDMI using colorspace: 1 *** BHDM: Waiting to transition to HDMI mode... 000CB001 0 *** BHDM: Waiting to transition to HDMI mode... 000CB001 0 *** BHDM: Waiting to transition to HDMI mode... 000CB001 0 *** BHDM: HDMI Output Mode: HDMI (Audio+Video) create surface 1920 1080 Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard parsing JPEG header.. JPEG Size: 1280x720 /flash/vmlinux.gz <5>Linux version 2.6.18-7.3-dm8000 (newnigma2@vs35) (gcc version 4.4.3 (GCC) ) #1 SMP Sat May 8 16:10:19 UTC 2010 Fetching vars from bootloader... none present, using defaults. Detected 256 MB on MEMC0 (strap 0x2219c310) <4>WARNING: read invalid MAC address ff:ff:ff:ff:ff:ff from flash @ 0xbffff824 Default command line = root=/dev/mtdblock3 rootfstype=jffs2 rw console=null 2 831ffed8 83040e98 g_board_RAM_size=256MB Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=1 CPU revision is: 0002a042 FPU revision is: 00130001 Determined physical RAM map: memory: 10000000 @ 00000000 (usable) ---> memsize from bootloader: 158 User-defined physical RAM map: node [00000000, 09e00000: RAM] node [09e00000, 06200000: RSVD] <5>Reserving 98 MB upper memory starting at 09e00000 <7>On node 0 totalpages: 65536 <7> DMA zone: 65536 pages, LIFO batch:15 Built 1 zonelists. Total pages: 65536 <5>Kernel command line: console=ttyS0,115200 root=/dev/mtdblock3 rootfstype=jffs2 rw before init RAC 0x01e0701f 0x0000000f 0x2fff0000 after init RAC 0x01e0705f 0x0000000f 0x2fff0000 ======> Before RAC_init:$22s5=00000020, $22s6(CBA)=11f0000c @B1F0_001C=00000001, @B1F0_0004=2fff0000, @B1F0_0000=01e0701f, @B1F0_0008=0000000f CBA = 11f00000 VALUE = 255 PAR_VAL2 = 0fff0000 RAC0 = b1f00000 RAC1 = b1f00008 RAC_RANGE = b1f00004 RAC_VALUE = 00087000 ******* Using CFE setting for RAC ******* $22s0=e30e3406, $22s5=00000020, $22s6=11f0000c Primary instruction cache 32kB, physically tagged, 2-way, linesize 64 bytes. Primary data cache 64kB, 4-way, linesize 64 bytes. Synthesized TLB refill handler (23 instructions). Synthesized TLB load handler fastpath (37 instructions). Synthesized TLB store handler fastpath (37 instructions). Synthesized TLB modify handler fastpath (36 instructions). PID hash table entries: 2048 (order: 11, 8192 bytes) Found MIPS counter frequency: 203 Mhz Using 202.501 MHz high precision timer. Console: colour dummy device 80x25 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 155264k/262144k available (3095k kernel code, 106640k reserved, 562k data, 152k init, 0k highmem) Mount-cache hash table entries: 512 Checking for 'wait' instruction... available. plat_prepare_cpus: ENABLING 2nd Thread... TP0: prom_boot_secondary: Kick off 2nd CPU... CPU revision is: 0002a042 FPU revision is: 00130001 Primary instruction cache 32kB, physically tagged, 2-way, linesize 64 bytes. Primary data cache 64kB, 4-way, linesize 64 bytes. Synthesized TLB refill handler (23 instructions). Brought up 2 CPUs migration_cost=1000 NET: Registered protocol family 16 registering PCI controller with io_map_base unset registering PCI controller with io_map_base unset SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI DEV in slot 1, ID=168c:001a PCI PnP: PCI_BAR[0] = ffff0000 PCI PnP: size requested is 10000 NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 4096) TCP reno registered brcm-pm: disabling power to USB block brcm-pm: disabling power to ENET block brcm-pm: disabling power to SATA block JFFS2 version 2.2. (NAND) (SUMMARY) (C) 2001-2006 Red Hat, Inc. Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x0 (irq = 65) is a 16550A brcm-pm: enabling power to ENET block Broadcom BCM7400 P42 Ethernet Network Device v2.0 May 8 2010 16:09:41 SUNDRY revision = 74000032, have IP Hdr Opt=1 Config Internal PHY Through MDIO: 100 MB Full-Duplex (auto-neg) brcm-pm: enabling power to SATA block ata1: SATA max UDMA/133 cmd 0xB0510000 ctl 0xB0510020 bmdma 0xB0510030 irq 42 ata2: SATA max UDMA/133 cmd 0xB0510100 ctl 0xB0510120 bmdma 0xB0510130 irq 42 scsi0 : sata_svw ata1: SATA link down (SStatus 4 SControl 300) ATA: abnormal status 0x7F on port 0xb051001c scsi1 : sata_svw ata2: SATA link up 1.5 Gbps (SStatus 113 SControl F0000) ata2.00: ATA-8, max UDMA/133, 3907029168 sectors: LBA48 NCQ (depth 0/32) ata2.00: configured for UDMA/133 Vendor: ATA Model: SAMSUNG HD203WI Rev: 1AN1 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 3907029168 512-byte hdwr sectors (2000399 MB) sda: Write Protect is off SCSI device sda: drive cache: write back SCSI device sda: 3907029168 512-byte hdwr sectors (2000399 MB) sda: Write Protect is off SCSI device sda: drive cache: write back sda: sda1 sd 1:0:0:0: Attached scsi disk sda sd 1:0:0:0: Attached scsi generic sg0 type 0 4587 kb/s - NAND PROBE: 2c da 80 15 NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Unknown NAND 256MiB 3,3V 8-bit) Scanning device for bad blocks Bad eraseblock 513 at 0x04020000 Bad eraseblock 1779 at 0x0de60000 Bad eraseblock 1953 at 0x0f420000 Bad eraseblock 2025 at 0x0fd20000 Creating 7 MTD partitions on "NAND 256MiB 3,3V 8-bit": 0x0000000000000000-0x0000000010000000 : "complete" 0x0000000000000000-0x0000000000100000 : "loader" 0x0000000000100000-0x0000000000400000 : "boot partition" 0x0000000000400000-0x0000000004000000 : "root partition" 0x0000000004000000-0x0000000008000000 : "home partition" 0x0000000008000000-0x000000000f800000 : "unused partition" 0x000000000f800000-0x0000000010000000 : "preset partition" ehci_hcd_brcm_init: Initializing 2 EHCI controller(s) brcm-pm: enabling power to USB block 10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (EHCI-brcm-0) drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller - USB h/w setup mode - USB power enable set for active LOW mode brcm-ehci brcm-ehci.0: BRCM EHCI brcm-ehci brcm-ehci.0: new USB bus registered, assigned bus number 1 brcm-ehci brcm-ehci.0: irq 62, io mem 0x10480300 brcm-ehci brcm-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected 10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (EHCI-brcm-1) drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller brcm-ehci-1 brcm-ehci-1.1: BRCM EHCI brcm-ehci-1 brcm-ehci-1.1: new USB bus registered, assigned bus number 2 brcm-ehci-1 brcm-ehci-1.1: irq 57, io mem 0x10480500 brcm-ehci-1 brcm-ehci-1.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ohci_hcd_brcm_init: Initializing 2 OHCI controller(s) 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-0) drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller - Resetting at b0480408 <-- brcm_start_hc brcm-ohci-0 brcm-ohci-0.0: BRCM OHCI brcm-ohci-0 brcm-ohci-0.0: new USB bus registered, assigned bus number 3 brcm-ohci-0 brcm-ohci-0.0: irq 63, io mem 0x10480400 usb 1-1: new high speed USB device using brcm-ehci and address 2 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-1) drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller - Resetting at b0480608 <-- brcm_start_hc brcm-ohci-1 brcm-ohci-1.1: BRCM OHCI brcm-ohci-1 brcm-ohci-1.1: new USB bus registered, assigned bus number 4 usb 1-1: configuration #1 chosen from 1 choice brcm-ohci-1 brcm-ohci-1.1: irq 64, io mem 0x10480600 hub 1-1:1.0: USB hub found hub 1-1:1.0: 3 ports detected usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usb 1-2: new high speed USB device using brcm-ehci and address 3 usb 1-2: configuration #1 chosen from 1 choice usb 2-1: new high speed USB device using brcm-ehci-1 and address 2 usb 2-1: configuration #1 chosen from 1 choice scsi2 : SCSI emulation for USB Mass Storage devices scsi3 : SCSI emulation for USB Mass Storage devices usbcore: registered new driver usb-storage USB Mass Storage support registered. i2c /dev entries driver TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 isa bounce pool size: 16 pages Vendor: Generic Model: USB SD Reader Rev: 1.00 Type: Direct-Access ANSI SCSI revision: 00 Vendor: TSSTcorp Model: CDDVDW SN-T083A Rev: SB01 Type: CD-ROM ANSI SCSI revision: 00 sd 2:0:0:0: Attached scsi removable disk sdb sd 2:0:0:0: Attached scsi generic sg1 type 0 Vendor: Generic Model: USB CF Reader Rev: 1.01 Type: Direct-Access ANSI SCSI revision: 00 sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 3:0:0:0: Attached scsi generic sg2 type 5 SCSI device sdc: 8027712 512-byte hdwr sectors (4110 MB) sdc: Write Protect is off sdc: assuming drive cache: write through VFS: Mounted root (jffs2 filesystem). Freeing unused kernel memory: 152k freed SCSI device sdc: 8027712 512-byte hdwr sectors (4110 MB) sdc: Write Protect is off sdc: assuming drive cache: write through sdc: sdc1 sd 2:0:0:1: Attached scsi removable disk sdc sd 2:0:0:1: Attached scsi generic sg3 type 0 Vendor: Generic Model: USB SM Reader Rev: 1.02 Type: Direct-Access ANSI SCSI revision: 00 sd 2:0:0:2: Attached scsi removable disk sdd sd 2:0:0:2: Attached scsi generic sg4 type 0 Vendor: Generic Model: USB MS Reader Rev: 1.03 Type: Direct-Access ANSI SCSI revision: 00 sd 2:0:0:3: Attached scsi removable disk sde sd 2:0:0:3: Attached scsi generic sg5 type 0 INIT: version 2.86 booting stb_core: module license 'Proprietary' taints kernel. FP Version 7 input: dreambox front panel as /class/input/input0 4014793 ms: 47 ms: 27 Starting /etc/rcS.d/S02sysfs... 11 ms: =s Startting the hotplug events dispatcher Synthesizing the initial hotplug events wlan: svn r3314 ath_hal: 2008-08-15 (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133, RF2425, REGOPS_FUNC, DFS, XR) ath_pci: svn r3314 Atheros HAL provided by OpenWrt, DD-WRT and MakSat Technologies MadWifi: ath_getchannels: HAL returned 26 channels. MadWifi: ath_getchannels: Channel 1 (2412 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 20 reg] Flags CF_CCK CF_2GHZ MadWifi: ath_getchannels: Channel 1 (2412 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 20 reg] Flags CF_OFDM CF_2GHZ MadWifi: ath_getchannels: Channel 2 (2417 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 20 reg] Flags CF_CCK CF_2GHZ MadWifi: ath_getchannels: Channel 2 (2417 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 20 reg] Flags CF_OFDM CF_2GHZ MadWifi: ath_getchannels: Channel 3 (2422 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 20 reg] Flags CF_CCK CF_2GHZ MadWifi: ath_getchannels: Channel 3 (2422 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 20 reg] Flags CF_OFDM CF_2GHZ MadWifi: ath_getchannels: Channel 4 (2427 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 20 reg] Flags CF_CCK CF_2GHZ MadWifi: ath_getchannels: Channel 4 (2427 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 20 reg] Flags CF_OFDM CF_2GHZ MadWifi: ath_getchannels: Channel 5 (2432 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 20 reg] Flags CF_CCK CF_2GHZ MadWifi: ath_getchannels: Channel 5 (2432 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 20 reg] Flags CF_OFDM CF_2GHZ MadWifi: ath_getchannels: Channel 6 (2437 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 20 reg] Flags CF_CCK CF_2GHZ MadWifi: ath_getchannels: Channel 6 (2437 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 20 reg] Flags CF_OFDM CF_2GHZ MadWifi: ath_getchannels: Channel 7 (2442 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 20 reg] Flags CF_CCK CF_2GHZ MadWifi: ath_getchannels: Channel 7 (2442 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 20 reg] Flags CF_OFDM CF_2GHZ MadWifi: ath_getchannels: Channel 8 (2447 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 20 reg] Flags CF_CCK CF_2GHZ MadWifi: ath_getchannels: Channel 8 (2447 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 20 reg] Flags CF_OFDM CF_2GHZ MadWifi: ath_getchannels: Channel 9 (2452 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 20 reg] Flags CF_CCK CF_2GHZ MadWifi: ath_getchannels: Channel 9 (2452 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 20 reg] Flags CF_OFDM CF_2GHZ MadWifi: ath_getchannels: Channel 10 (2457 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 20 reg] Flags CF_CCK CF_2GHZ MadWifi: ath_getchannels: Channel 10 (2457 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 20 reg] Flags CF_OFDM CF_2GHZ MadWifi: ath_getchannels: Channel 11 (2462 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 20 reg] Flags CF_CCK CF_2GHZ MadWifi: ath_getchannels: Channel 11 (2462 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 20 reg] Flags CF_OFDM CF_2GHZ MadWifi: ath_getchannels: Channel 12 (2467 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 20 reg] Flags CF_CCK CF_2GHZ MadWifi: ath_getchannels: Channel 12 (2467 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 20 reg] Flags CF_OFDM CF_2GHZ MadWifi: ath_getchannels: Channel 13 (2472 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 20 reg] Flags CF_CCK CF_2GHZ MadWifi: ath_getchannels: Channel 13 (2472 MHz) Max Tx Power 16 dBm (hw limited) [16 hw 20 reg] Flags CF_OFDM CF_2GHZ MadWifi: ath_attach: Switching rfkill capability off ath_rate_sample: 1.2 (svn r3314) MadWifi: ath_attach: Switching per-packet transmit power control off wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps wifi0: H/W encryption support: WEP AES AES_CCM TKIP wifi0: ath_announce: Use hw queue 1 for WME_AC_BE traffic wifi0: ath_announce: Use hw queue 0 for WME_AC_BK traffic wifi0: ath_announce: Use hw queue 2 for WME_AC_VI traffic wifi0: ath_announce: Use hw queue 3 for WME_AC_VO traffic wifi0: ath_announce: Use hw queue 8 for CAB traffic wifi0: ath_announce: Use hw queue 9 for beacons ath_pci: wifi0: Atheros 2413: mem=0xd1000000, irq=33 Waiting for /dev to be fully populated done 4756 ms: 29 Starting /etc/rcS.d/S03udev... 13 ms: =s 16 ms: 31 Starting /etc/rcS.d/S04bootup... ln: /dev/dbox/lc17 ms: 10 d0: File exists kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. 850 ms: 11 21 ms: 12 modprobe: module nfsd not found in modules.dep fuse init (API version 7.7) modprobe: module tun not found in modules.dep modprobe: module ipv6 not found in modules.dep 697 ms: 13 10 ms: 14 1 ms: 15 30 ms: 16 1 ms: 17 input: dreambox remote control (native) as /class/input/input1 input: dreambox advanced remote control (native) as /class/input/input2 input: dreambox ir keyboard as /class/input/input3 input: dreambox ir mouse as /class/input/input4 modprobe: module info not found in modules.dep fpga init done OK 0 enter base init, xvd 20090807, vdc 20090807, rap 20090430, xpt 20090430 !!! kernMemSize: 158 MB smca set muxes smcb set muxes smcc set muxes SMCA: controller reset timed out SMCB: controller reset timed out maskffffffff using fpga version 2a tsmux set tsports reg 02 to val dc tsmux set tsports reg 02 to val dc tsmux set tsports reg 03 to val fe tsmux set tsports reg 03 to val fe tsmux set cisource reg 00 to val 55 tsmux set cisource reg 00 to val 55 tsmux set cisource reg 01 to val 55 tsmux set cisource reg 01 to val 55 register adapter register adapter register adapter register adapter register adapter HDMI: device attached set sb to 3(2) set fb to 2(-1) set input to 0 set fb to 2(-1) bcm_video_analog_port_setup (fmt=7) SET FORMAT: display[1], format=7 display 0 uses vbi path 1 display 1 uses vbi path 0 HDMI: hotplug handler! Write AVS: 00 00 00 00 00 00 00 03 00 00 00 00 00 00 Write AVS: 00 00 00 00 00 00 18 63 00 00 00 00 00 00 set sb to 3(2) Write AVS: 40 40 00 00 00 00 00 03 00 02 00 00 00 ff set sb to 3(2) using 50.00Hz as MonitorRefreshRate SET FORMAT: display[0], format=34 HDMI detected HDMI mode use EDID to detect colorspace using colorspace: 1 set fb to 2(0) bcm_video_analog_port_setup (fmt=7) SET FORMAT: display[1], format=7 disable wss on display 0 disable wss on display 1 bcmfb: creating surface with pixel format 0x07e48888 (BPXL_eA8_R8_G8_B8) udevd-event[830]: node_symlink: rename(/dev/fb.udev-tmp, /dev/fb) failed: Is a directory enable mad VIDEO0: set fallback framerate to 60000 VIDEO0: set progressive override mode to 1 VIDEO0: set streamtype! set MPEG2 sw rave disabled! enable mad VIDEO1: set fallback framerate to 60000 VIDEO1: set progressive override mode to 1 VIDEO1: set streamtype! set MPEG2 sw rave disabled! set ac3 to downmix set aac to downmix DVB: registering new adapter (BCM7400). autodetecting NIMs... ret: -145 ret: -145 Initializing adapter 0 (BCM4501 (internal)-DVB-S2) bcm4501: found 4501, revision 2(c0) bcm_initAP BCM4501: upload & start firmware DVB: registering frontend 0 (bcm4501)... Initializing adapter 1 (BCM4501 (internal)-DVB-S2) DVB: registering frontend 0 (bcm4501)... CI removed... CI removed... CI removed... CI removed... init ALSA! vdc pip init workaround sync is off so we enable it playback! total video delay: 0 (0 ms) VIDEO1: start decode flush video decoder VIDEO1 got pts failed !!!! (ret 0) VIDEO1: first pts 0x0 VIDEO1: framerate changed 8 VIDEO1: resolution changed (720 576) VIDEO1: aspect changed 2 VIDEO1: stop decode no decoder left in sync handling so disable xpt_sync 9923 ms: 20 35 ms: 22 VIDEO0: set blank to 0 sync is off so we enable it playback! total video delay: 0 (0 ms) 24 ms: 23 VIDEO0: start decode flush video decoder VIDEO0 got pts failed !!!! (ret 0) 7 ms: 24 dev.cdrom.lock = 0 30 ms: 25 2 ms: 26 VIDEO0: first pts 0x0 VIDEO0: framerate changed 3 VIDEO0: resolution changed (1280 720) VIDEO0: aspect changed 3 19 ms: 27 ############################################################ ############### MOUNT USB STORAGE ###################### ############################################################ set current avs auto aspect to 16:9 disable wss on display 0 disable wss on display 1 set current avs auto aspect to 16:9 disable wss on display 0 disable wss on display 1 set sb to 3(1) Write AVS: 40 40 00 00 00 00 00VIDEO0: set blank to 0 01 00 02 00 00 00 ff VIDEO0: stop decode VIDEO0: set blank to 0 no decoder left in sync handling so disable xpt_sync Mount /dev/sdc1 (ext3) on /autofs/3f3817fd-f7a8-43ef-a62c-367458596e94 ldconfig: Can't open configuration file /etc/ld.so.conf: No such file or directory kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on sdc1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. cdfs 2.6.18 loaded. mount: mounting /dev/sr0 on /autofs/sr0 failed: No medium found 9706 ms: 28 766 ms: 29 11 ms: 30 11 ms: =s Starting system message bus: dbus. 443 ms: 33 Starting /etc/rcS.d/S05dbus-1... 12 ms: =s 60 ms: 35 Starting /etc/rcS.d/S10tpmd... 17 ms: =s usbcore: registered new driver usbserial drivers/usb/serial/usb-serial.c: USB Serial support registered for generic usbcore: registered new driver usbserial_generic drivers/usb/serial/usb-serial.c: USB Serial Driver core drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303 usbcore: registered new driver pl2303 drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver drivers/usb/serial/usb-serial.c: USB Serial support registered for FTDI USB Serial Device usbcore: registered new driver ftdi_sio drivers/usb/serial/ftdi_sio.c: v1.4.3:USB FTDI Serial Converters Driver 559 ms: 37 Starting /etc/rcS.d/S20modutils.sh... 11 ms: =s * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon [ ok ] 432 ms: 39 Starting /etc/rcS.d/S21avahi-daemon... 11 ms: =s * Starting Avahi Unicast DNS Configuration Daemon: avahi-dnsconfd [ ok ] 319 ms: 41 Starting /etc/rcS.d/S22avahi-dnsconfd... 18 ms: =s 67 ms: 43 Starting /etc/rcS.d/S38devpts.sh... 19 ms: =s Configuring network interfaces... eth0 no wireless extensions. udhcpc (v1.15.3) started Sending discover... Sending select for 192.168.1.29... Lease of 192.168.1.29 obtained, lease time 864000 adding dns 192.168.1.1 done. 1945 ms: 45 Starting /etc/rcS.d/S40networking... 13 ms: =s Starting rdate timesync...: Sync797 ms: 47 Starting /etc/rcS.d/S41rdate... failed12 ms: =s Starting portmap daemon: portmap. 52 ms: 49 Starting /etc/rcS.d/S43portmap... INIT: Entering runlevel: 3 system message bus already started; not starting. Starting system message bus: /usr/bin/dbus-daemon is already running 988 Starting Dropbear SSH server: dropbear. Starting internet superserver: inetd. Starting syslogd/klogd: done * starting FTP Server: vsftpd... chown: unknown user ftp * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon [ ok ] * Starting Avahi Unicast DNS Configuration Daemon: avahi-dnsconfd * starting eDaemon: eDaemon... done. [SCRIPT] start: CCcam 2.1.4 VIDEO0: set blank to 0 sync is off so we enable it playback! total video delay: 0 (0 ms) VIDEO0: start decode flush video decoder VIDEO0: first pts 0x0 VIDEO0: set blank to 0 VIDEO0: stop decode VIDEO0: set blank to 0 no decoder left in sync handling so disable xpt_sync SMCB: invalid ioctl: 0x8004730a SMCC: iso7816: cannot read T1 header (ret=-145) SMCC: iso7816: error in receive SMCB: invalid ioctl: 0x8004730a SMCC: iso7816: cannot read T1 header (ret=-145) SMCC: iso7816: error in receive SMCC: invalid data SMCB: invalid ioctl: 0x8004730a SMCC: iso7816: cannot read T1 header (ret=-145) SMCC: iso7816: error in receive SMCB: invalid ioctl: 0x8004730a SMCC: iso7816: cannot read T1 header (ret=-145) SMCC: iso7816: error in receive SMCC: invalid data SMCC: iso7816: cannot read T1 header (ret=-145) SMCC: iso7816: error in receive SMCB: invalid ioctl: 0x8004730a SMCC: iso7816: cannot read T1 header (ret=-145) SMCC: iso7816: error in receive SMCC: invalid data SMCB: invalid ioctl: 0x8004730a SMCB: invalid ioctl: 0x8004730a SMCB: invalid ioctl: 0x8004730a SMCB: invalid ioctl: 0x8004730a SMCB: invalid ioctl: 0x8004730a SMCB: invalid ioctl: 0x8004730a SMCB: invalid ioctl: 0x8004730a SMCB: invalid ioctl: 0x8004730a SMCB: invalid ioctl: 0x8004730a SMCB: invalid ioctl: 0x8004730a SMCB: invalid ioctl: 0x8004730a SMCB: invalid ioctl: 0x8004730a SMCB: invalid ioctl: 0x8004730a SMCB: invalid ioctl: 0x8004730a SMCB: invalid ioctl: 0x8004730a SMCB: invalid ioctl: 0x8004730a SMCB: invalid ioctl: 0x8004730a SMCB: invalid ioctl: 0x8004730a SMCB: invalid ioctl: 0x8004730a SMCB: invalid ioctl: 0x8004730a SMCB: invalid ioctl: 0x8004730a SMCB: invalid ioctl: 0x8004730a