800 Bootet nicht!!!!!

greho · 3. März 2011, 10:38

Hallo Gemeinde!!
Gestern abend hat sich meine DM 800 von alleine ausgeschaltet und boote nicht mehr.
Habe dann wieder Newenigma 3.15 aufgespielt und der balken auf dem display geht nicht weiter zeigt nur Newenigma logo und please weit und geht nicht weiter.
Dann habe die Dreambox Multimedia Firmware augespielt und das gleiche spiel Dreambox bootet nicht mehr.
Was soll ich machen damit die box Bootet???
Danke

=sven= · 3. März 2011, 10:41

ein bootlog würde helfen

greho · 3. März 2011, 10:43

wie soll ich das ablesen????

=sven= · 3. März 2011, 10:45

Bootlog erstellen

greho · 3. März 2011, 11:23

kann man das nicht staat mit ComPort mit netzwerk machen im meinem laptop befindet sich kein RS 232????

Gong · 3. März 2011, 11:26

Bootlog geht nur so. Wenn man keinen seriellen Anschluss mehr hat dann kann man einen USB to RS 232 Adapert verwenden.

Bei neueren Boxen die keinen seriellen Anschluss haben geht es über die USB Serviceschnitstelle.

=sven= · 3. März 2011, 11:54

probier mal, vllt ist enigma2 schon gestartet:
telnet %boxIP%

Quellcode

init 4
enigma2.sh

greho · 3. März 2011, 11:58

ich habe orginal Firmware jetzt drauf!!!

greho · 4. März 2011, 09:18

Hier der ausgelesene Bottlog:

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.03.04 09:15:40 =~=~=~=~=~=~=~=~=~=~=~=

(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.

Dreambox D M800

FIRST STAGE 1.00 {BO23456}
[m

2ND STAGE OK, build #76 (20100419)

0.000 - BCM board setup
{00000126,00000126,00000125,00000124,00000123,00000133}
0.007 - fp init
0.008 - ca init
0.723 - load config
dCA: not existent, loading defaults
0.754 - config loaded.
* press to enter setup
OLED found!
BOOT #76(20100419)
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++
dreamupd initialized
Scanning JFFS2 FS: . | / - \ | / - \ | / - \ | / done.

/flash/bootlogo.elf
bootlogo size: 285065
using 1280x720p (60.00 Hz)
Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <luc@saillard.org>
parsing JPEG header..
JPEG Size: 1280x720
/flash/vmlinux.gz
<5>Linux version 2.6.18-7.4-dm800 (tmbinc@pepe.multimedia-labs.de) (gcc version 4.4.3 (GCC) ) #1 Wed Dec 15 22:20:39 UTC 2010
Fetching vars from bootloader... none present, using defaults.
board_init_once: regval=04ac6502, ddr_strap=3, 4 chips, pci_size=2
Detected 256 MB on board
<4>WARNING: read invalid MAC address ff:ff:ff:ff:ff:ff from flash @ 0xbffff824
Default command line =
root=/dev/mtdblock3 rootfstype=jffs2 rw console=null
1 831ffed8 8303c848
g_board_RAM_size=256MB
Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=0
CPU revision is: 00020000
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
---> memsize from bootloader: 148
User-defined physical RAM map:
node [00000000, 09400000: RAM]
node [09400000, 06c00000: RSVD]
<5>Reserving 108 MB upper memory starting at 09400000
<7>On node 0 totalpages: 65536
<7> DMA zone: 65536 pages, LIFO batch:15
Built 1 zonelists. Total pages: 65536
<5>Kernel command line: root=/dev/mtdblock3 rootfstype=jffs2 rw console=null
before init RAC 0x02a00000 0x00000000
after init RAC 0x02a0000f 0x0fff0000

greho · 4. März 2011, 10:31

im moment habe ich orginale software von Dream Multimedia drauf!

nixkoenner · 4. März 2011, 11:14

Original von greho
im moment habe ich orginale software von Dream Multimedia drauf!

<5>Kernel command line: root=/dev/mtdblock3 rootfstype=jffs2 rw console=null

die zeile must du umstellen sonst kommt kein bootlog console=null <= debug aus

greho · 4. März 2011, 11:22

schön!!
aber wie mache ich das??

sparksofinsanity · 4. März 2011, 11:24

Im Bios, die Box in den "Stop Modus" versetzen und dich anschließend per Telnet verbinden.

Gong · 4. März 2011, 11:26

Du bringst die Box in den Stop Modus also so als würdest du sie über den Browser flashen wollen. Da bekommst du ja auch die IP Adresse angezeigt.

Dann gehst du ins Putty und stellst eine Verbindung her.

So gelangst du dann ins Bios und kannst die command line ändern.

Wie es aber genau geht ist hier schön erklälert: Bootlog erstellen

greho · 4. März 2011, 11:29

ich flasche jetzt Newenigma 3.16 über Dreamup was soll ich dann machen??

greho · 4. März 2011, 11:30

welche comands soll ich ändern???

Gong · 4. März 2011, 11:43

Flash das Image und schau ob die Box hoch fährt und alles geht. Wenn nicht dann gehst du bitte nach der Anleitung vor:

Bootlog erstellen

Die commandline musst du auf so abändern:

DM 800/8000:
console=ttyS0,115200 root=/dev/mtdblock3 rootfstype=jffs2 rw

Aber das steht alles oben in der Anleitung zum Bootlog.

greho · 5. März 2011, 09:05

leute ich komme damit nicht klar!
kann mir jemand sagen was hier falsch ist??
ich habe alles gemacht nach der Anleitung und die Box geht nicht hoch!!
(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM800
FIRST STAGE 1.00 {BO23456}

2ND STAGE OK, build #82 (2011-02-25)

0.000 - BCM board setup
{00000126,00000126,00000125,00000124,00000123,00000133}
0.007 - fp init
0.008 - ca init
0.732 - load config
0.760 - config loaded.
* press to enter setup
OLED found!
lcd: BOOT #82
- read config file: /boot/secondstage.conf
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++
dreamupd initialized
Scanning JFFS2 FS: . done.
find_inode failed for name=secondstage.conf
load: Failed to find inode
- failed to open /boot/secondstage.conf
- failed to open /cf/autorun.bat
lcd: /flash/bootlogo.elf
bootlogo size: 35911
*** BCHP: Invalid RTS setting detected. Forcing MEMC_0_CLIENT_INFO_7 (AVD_CAB_0) RR to true. Please see latest 7401 RTS documentation.
no HDMI device detected
no HDMI mode available, reverting to 720p
using 1280x720p (60.00 Hz)
create surface 1280 720
Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <luc@saillard.org>
parsing JPEG header..
Virtual FB Size: 1280x720
lcd: /flash/vmlinux.gz
<5>Linux version 2.6.18-7.4-dm800 (newnigma2@vs35) (gcc version 4.4.3 (GCC) ) #1 Tue Feb 8 09:11:26 UTC 2011
Fetching vars from bootloader... none present, using defaults.
board_init_once: regval=44ac6502, ddr_strap=3, 4 chips, pci_size=2
Detected 256 MB on board
<4>WARNING: read invalid MAC address ff:ff:ff:ff:ff:ff from flash @ 0xbffff824
Default command line =
root=/dev/mtdblock3 rootfstype=jffs2 rw console=null
2 831ffeb8 83029368
g_board_RAM_size=256MB
Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=0
CPU revision is: 00020000
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
---> memsize from bootloader: 148
User-defined physical RAM map:
node [00000000, 09400000: RAM]
node [09400000, 06c00000: RSVD]
<5>Reserving 108 MB upper memory starting at 09400000
<7>On node 0 totalpages: 65536
<7> DMA zone: 65536 pages, LIFO batch:15
Built 1 zonelists. Total pages: 65536
<5>Kernel command line: console=ttySO,115200 root=/devmtdblock3 rootfstype=jffs2rw
before init RAC 0x02a00000 0x00000000
after init RAC 0x02a0000f 0x0fff0000

(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM800
FIRST STAGE 1.00 {BO23456}

2ND STAGE OK, build #82 (2011-02-25)

0.000 - BCM board setup
{00000126,00000126,00000125,00000124,00000123,00000133}
0.007 - fp init
0.008 - ca init
0.733 - load config
0.761 - config loaded.
* press [S] to enter setup
OLED found!
lcd: BOOT #82
- read config file: /boot/secondstage.conf
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++
dreamupd initialized
Scanning JFFS2 FS: . done.
find_inode failed for name=secondstage.conf
load: Failed to find inode
- failed to open /boot/secondstage.conf
- failed to open /cf/autorun.bat
lcd: /flash/bootlogo.elf
bootlogo size: 35911
*** BCHP: Invalid RTS setting detected. Forcing MEMC_0_CLIENT_INFO_7 (AVD_CAB_0) RR to true. Please see latest 7401 RTS documentation.
no HDMI device detected
no HDMI mode available, reverting to 720p
using 1280x720p (60.00 Hz)
create surface 1280 720
Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <luc@saillard.org>
parsing JPEG header..
Virtual FB Size: 1280x720
lcd: /flash/vmlinux.gz
<5>Linux version 2.6.18-7.4-dm800 (newnigma2@vs35) (gcc version 4.4.3 (GCC) ) #1 Tue Feb 8 09:11:26 UTC 2011
Fetching vars from bootloader... none present, using defaults.
board_init_once: regval=44ac6502, ddr_strap=3, 4 chips, pci_size=2
Detected 256 MB on board
<4>WARNING: read invalid MAC address ff:ff:ff:ff:ff:ff from flash @ 0xbffff824
Default command line =
root=/dev/mtdblock3 rootfstype=jffs2 rw console=null
2 831ffeb8 83029368
g_board_RAM_size=256MB
Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=0
CPU revision is: 00020000
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
---> memsize from bootloader: 148
User-defined physical RAM map:
node [00000000, 09400000: RAM]
node [09400000, 06c00000: RSVD]
<5>Reserving 108 MB upper memory starting at 09400000
<7>On node 0 totalpages: 65536
<7> DMA zone: 65536 pages, LIFO batch:15
Built 1 zonelists. Total pages: 65536
<5>Kernel command line: console=ttySO,115200 root=/devmtdblock3 rootfstype=jffs2rw
before init RAC 0x02a00000 0x00000000
after init RAC 0x02a0000f 0x0fff0000

(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM800
FIRST STAGE 1.00 {BO23456}

2ND STAGE OK, build #82 (2011-02-25)

0.000 - BCM board setup
{00000126,00000126,00000125,00000124,00000123,00000133}
0.007 - fp init
0.008 - ca init
0.731 - load config
0.759 - config loaded.
* press [S] to enter setup
OLED found!
lcd: BOOT #82
- read config file: /boot/secondstage.conf
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++
dreamupd initialized
Scanning JFFS2 FS: . done.
find_inode failed for name=secondstage.conf
load: Failed to find inode
- failed to open /boot/secondstage.conf
- failed to open /cf/autorun.bat
lcd: /flash/bootlogo.elf
bootlogo size: 35911
*** BCHP: Invalid RTS setting detected. Forcing MEMC_0_CLIENT_INFO_7 (AVD_CAB_0) RR to true. Please see latest 7401 RTS documentation.
no HDMI device detected
no HDMI mode available, reverting to 720p
using 1280x720p (60.00 Hz)
create surface 1280 720
Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <luc@saillard.org>
parsing JPEG header..
Virtual FB Size: 1280x720
lcd: /flash/vmlinux.gz
<5>Linux version 2.6.18-7.4-dm800 (newnigma2@vs35) (gcc version 4.4.3 (GCC) ) #1 Tue Feb 8 09:11:26 UTC 2011
Fetching vars from bootloader... none present, using defaults.
board_init_once: regval=44ac6502, ddr_strap=3, 4 chips, pci_size=2
Detected 256 MB on board
<4>WARNING: read invalid MAC address ff:ff:ff:ff:ff:ff from flash @ 0xbffff824
Default command line =
root=/dev/mtdblock3 rootfstype=jffs2 rw console=null
2 831ffeb8 83029368
g_board_RAM_size=256MB
Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=0
CPU revision is: 00020000
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
---> memsize from bootloader: 148
User-defined physical RAM map:
node [00000000, 09400000: RAM]
node [09400000, 06c00000: RSVD]
<5>Reserving 108 MB upper memory starting at 09400000
<7>On node 0 totalpages: 65536
<7> DMA zone: 65536 pages, LIFO batch:15
Built 1 zonelists. Total pages: 65536
<5>Kernel command line: console=ttySO,115200 root=/devmtdblock3 rootfstype=jffs2rw
before init RAC 0x02a00000 0x00000000
after init RAC 0x02a0000f 0x0fff0000

(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM800
FIRST STAGE 1.00 {BO23456}

2ND STAGE OK, build #82 (2011-02-25)

0.000 - BCM board setup
{00000126,00000126,00000125,00000124,00000123,00000133}
0.007 - fp init
0.008 - ca init
0.736 - load config
0.764 - config loaded.
* press [S] to enter setup
OLED found!
lcd: BOOT #82
- read config file: /boot/secondstage.conf
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++
dreamupd initialized
Scanning JFFS2 FS: . done.
find_inode failed for name=secondstage.conf
load: Failed to find inode
- failed to open /boot/secondstage.conf
- failed to open /cf/autorun.bat
lcd: /flash/bootlogo.elf
bootlogo size: 35911
*** BCHP: Invalid RTS setting detected. Forcing MEMC_0_CLIENT_INFO_7 (AVD_CAB_0) RR to true. Please see latest 7401 RTS documentation.
no HDMI device detected
no HDMI mode available, reverting to 720p
using 1280x720p (60.00 Hz)
create surface 1280 720
Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <luc@saillard.org>
parsing JPEG header..
Virtual FB Size: 1280x720
lcd: /flash/vmlinux.gz
<5>Linux version 2.6.18-7.4-dm800 (newnigma2@vs35) (gcc version 4.4.3 (GCC) ) #1 Tue Feb 8 09:11:26 UTC 2011
Fetching vars from bootloader... none present, using defaults.
board_init_once: regval=44ac6502, ddr_strap=3, 4 chips, pci_size=2
Detected 256 MB on board
<4>WARNING: read invalid MAC address ff:ff:ff:ff:ff:ff from flash @ 0xbffff824
Default command line =
root=/dev/mtdblock3 rootfstype=jffs2 rw console=null
2 831ffeb8 83029368
g_board_RAM_size=256MB
Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=0
CPU revision is: 00020000
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
---> memsize from bootloader: 148
User-defined physical RAM map:
node [00000000, 09400000: RAM]
node [09400000, 06c00000: RSVD]
<5>Reserving 108 MB upper memory starting at 09400000
<7>On node 0 totalpages: 65536
<7> DMA zone: 65536 pages, LIFO batch:15
Built 1 zonelists. Total pages: 65536
<5>Kernel command line: console=ttySO,115200 root=/devmtdblock3 rootfstype=jffs2rw
before init RAC 0x02a00000 0x00000000
after init RAC 0x02a0000f 0x0fff0000

(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM800
FIRST STAGE 1.00 {BO23456}

2ND STAGE OK, build #76 (20100419)

0.000 - BCM board setup
{00000126,00000126,00000125,00000124,00000123,00000133}
0.007 - fp init
0.008 - ca init
0.723 - load config
dCA: not existent, loading defaults
0.754 - config loaded.
* press [S] to enter setup
OLED found!
BOOT #76(20100419)
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++
dreamupd initialized
Scanning JFFS2 FS: . done.
/flash/bootlogo.elf
bootlogo size: 285065
using 1280x720p (60.00 Hz)
Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <luc@saillard.org>
parsing JPEG header..
JPEG Size: 1280x720
/flash/vmlinux.gz
<5>Linux version 2.6.18-7.4-dm800 (tmbinc@pepe.multimedia-labs.de) (gcc version 4.4.3 (GCC) ) #1 Wed Dec 15 22:20:39 UTC 2010
Fetching vars from bootloader... none present, using defaults.
board_init_once: regval=04ac6502, ddr_strap=3, 4 chips, pci_size=2
Detected 256 MB on board
<4>WARNING: read invalid MAC address ff:ff:ff:ff:ff:ff from flash @ 0xbffff824
Default command line =
root=/dev/mtdblock3 rootfstype=jffs2 rw console=null
1 831ffed8 8303c848
g_board_RAM_size=256MB
Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=0
CPU revision is: 00020000
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
---> memsize from bootloader: 148
User-defined physical RAM map:
node [00000000, 09400000: RAM]
node [09400000, 06c00000: RSVD]
<5>Reserving 108 MB upper memory starting at 09400000
<7>On node 0 totalpages: 65536
<7> DMA zone: 65536 pages, LIFO batch:15
Built 1 zonelists. Total pages: 65536
<5>Kernel command line: root=/dev/mtdblock3 rootfstype=jffs2 rw console=null<= debug aus
before init RAC 0x02a00000 0x00000000
after init RAC 0x02a0000f 0x0fff0000

sparksofinsanity · 5. März 2011, 09:18

console=ttyS0,115200 root=/dev/mtdblock3 rootfstype=jffs2 rw <- einfach nur 1:1 übernehmen

<5>Kernel command line: console=ttySO,115200 root=/devmtdblock3 rootfstype=jffs2rw

Wenn du da ein O aus der Null machst kann das auch nichts werden

greho · 5. März 2011, 09:29

wie 1.:1 übernehmen????

Quellcode

Teilen