booten vom cf

    • booten vom cf

      Hallo zusammen,

      ich bin neu hier und erstmals möchte ich mich bedanken fürs tolles image was ich erfolgreich eingespielt habe. :D

      Dann habe ich wie beschrieben alles auf die cf karte verschoben und ohne Probleme auch upgedatet usw. 8)

      Jetzt meine Frage:
      Das Booten (tiefe Neustart) über die cf Karte dauert ca 15min. Ist das Normal??? ?( ?(

      Mfg
      kostar

    • nein keine netzwerkfreigaben o.ä.
      das image ist "jungfreulich" 1:1 vom flash eingespielt.
      Boote vom flash, geht schnell 1-3 min.
      Boote vom cf, kommt das newenigma2 logo, lädt linux.gz, dann schwarzes bild im fernsehen, und auf dem lcd des 7025 steht "dream multimedia" und der "balken" bleibt ca. 15 min. stehen bis er weiter hochfährt. (e2 neustart geht auch normal! - nur das tiefe neustart dauert ewig).

      Das gleiches habe ich auf zwei 7025, die ich genauso neugeflasht habe.
      cf ist von transcend 4gb x133 (steht so drauf).
      wlan stick (orig.dm) via usb ist auch dabei.

      LG
      kostar

      Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von kostar ()

    • danke für die rasche Antwort.

      ich hab versucht bootlog zu erstellen, allerdings wenn ich die commandzeile laut anweisung ändere, dann bootet er vom cf (anfänglich sieht zumindest so aus) und dann (also nach dem laden der Firmware vermute...) geht aufs flash weiter.... innerhalb von 1-2 minuten ist er fertig ohne Verzögerung ohne nix ABER vom flash gebootet und nicht vom cf.

      Stelle ich wieder das BIOS auf Factory RESET, (also ohne die Command Line) bekomme ich folgendes bootlog:

      Brainfuck-Quellcode

      1. =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.11.25 16:29:55 =~=~=~=~=~=~=~=~=~=~=~=
      2. *
      3. Dreambox D M7025
      5. FIRST STAGE 1.4 {2345}
      6. [m
      8. 2ND STAGE OK, build #83 (2011-02-28)
      10. 0.000 - DM7025 board setup
      11. 0.002 - initializing PCI...
      12. 0.012 - done!
      13. 0.014 - fp init
      14. FP version 7 detected
      15. 0.154 - ca init
      16. RSA key 1 is used.
      17. 0.259 - load config
      18. dCA: not existent, loading defaults
      19. 0.842 - config loaded.
      20. * press [S] to enter setup
      21. 7831152 sectors (3823 MB)
      22. P 06 1 10079 < 7831152
      23. OLED found!
      24. lcd: BOOT #83
      25. - read config file: /boot/secondstage.conf
      26. detected jffs2 blocksize: 16kb
      27. +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
      28. +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
      29. +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
      30. +++++++++++++++++++++++++++++++++++++++++++++++++++
      31. dreamupd initialized
      32. Scanning JFFS2 FS: . | / - \ | / - \ | / - \ | / done.
      34. find_inode failed for name=secondstage.conf
      36. load: Failed to find inode
      38. - failed to open /boot/secondstage.conf
      39. lcd: CF AVAILABLE
      40. +CF
      42. Device 2: Partition 1: Filesystem: FAT32 "BOOTFS"
      43. lcd: /cf/bootlogo.elf
      44. bootlogo size: 49877
      45. vscale: 576:576
      46. lcd: /cf/vmlinux.gz
      48. LINUX started...
      49. ATI Xilleon 226 (little endian), Solo mode
      50. PCI bus speed is 33MHz
      51. Initializing IRQs
      52. about to enable interrupts!
      53. interrupts enabled.
      54. Linux version 2.6.12.6 (newnigma2@vs35) (gcc version 4.4.3 (GCC) ) #1 Tue Feb 8 07:31:50 UTC 2011
      55. memsize: 77MB
      56. Xilleon REG value before setting: PAD_USB1: 0xf43, PAD_USB2: 0xf43
      57. Xilleon REG value after setting: PAD_USB1: 0xf43, PAD_USB2: 0xf43
      58. CPU revision is: 00018448
      59. Determined physical RAM map:
      60. memory: 00080000 @ 00000000 (ROM data)
      61. memory: 00080000 @ 00080000 (reserved)
      62. memory: 04c00000 @ 00100000 (usable)
      63. Built 1 zonelists
      64. Kernel command line: root=/dev/hdc2 rootfstype=ext3 console=ttyS0,115200 rw
      65. Primary instruction cache 16kB, physically tagged, 4-way, linesize 16 bytes.
      66. Primary data cache 16kB, 4-way, linesize 16 bytes.
      67. Synthesized TLB refill handler (20 instructions).
      68. Synthesized TLB load handler fastpath (32 instructions).
      69. Synthesized TLB store handler fastpath (32 instructions).
      70. Synthesized TLB modify handler fastpath (31 instructions).
      71. PID hash table entries: 512 (order: 9, 8192 bytes)
      72. calculating r4koff... CPU frequency 299.68 MHz
      73. Using 149.838 MHz high precision timer.
      74. Console: colour dummy device 80x25
      75. Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
      76. Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
      77. Memory: 72960k/77824k available (2862k kernel code, 4700k reserved, 813k data, 124k init, 0k highmem)
      78. Mount-cache hash table entries: 512
      79. Checking for 'wait' instruction... available.
      80. NET: Registered protocol family 16
      81. Can't analyze prologue code at 803c9990
      82. PCI init - ohwe, ohwe..
      83. SCSI subsystem initialized
      84. usbcore: registered new driver usbfs
      85. usbcore: registered new driver hub
      86. irq fixup slot 10 vendor 10ec irq 33
      87. TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
      88. inotify device minor=63
      89. devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
      90. devfs: boot_options: 0x0
      91. JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
      92. Initializing Cryptographic API
      93. Serial: 8250/16550 driver $Revision: 1.90 $ 6 ports, IRQ sharing disabled
      94. ttyS0 at MMIO 0x0 (irq = 100) is a 16550A
      95. ttyS1 at MMIO 0x0 (irq = 99) is a 16550A
      96. io scheduler noop registered
      97. io scheduler anticipatory registered
      98. io scheduler deadline registered
      99. io scheduler cfq registered
      100. 8139too Fast Ethernet driver 0.9.27
      101. RTL8139 EEPROM CONTENT: 8129 10ec 8139 10ec 8139 2020 e512 0900 0034 0000
      102. eth0: RealTek RTL8139 at 0x2000, 00:09:34:1c:3c:78, IRQ 33
      103. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
      104. ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
      105. X226: IDE controller at PCI slot 0000:00:14.1
      106. X226: chipset revision 1
      107. X226: 100% native mode on irq 3
      108. hwif->channel: 0, hwif->index: 0
      109. ide0: BM-DMA at 0x2400-0x2407, BIOS settings: hda:DMA, hdb:DMA
      110. init_hwif_xilleon, 0, mate: 00000000
      111. hwif->channel: 0, hwif->index: 1
      112. ide1: BM-DMA at 0x2400-0x2407, BIOS settings: hdc:DMA, hdd:DMA
      113. init_hwif_xilleon, 1, mate: 804ce0d8
      114. select 1
      115. hdc: TS4GCF133, ATA DISK drive
      116. hdc: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
      117. hdc: set_drive_speed_status: error=0x04 { DriveStatusError }
      118. ide1 at 0x2410-0x2417,0x2422 on irq 3
      119. select 0
      120. hda: WDC WD5000AVJB-63J1A0, ATA DISK drive
      121. ide0 at 0x2410-0x2417,0x2422 on irq 3 (shared with ide1)
      122. hdc: max request size: 128KiB
      123. hdc: 7831152 sectors (4009 MB) w/1KiB Cache, CHS=7769/16/63
      124. hdc: cache flushes not supported
      125. /dev/ide/host1/bus0/target0/lun0:select 1
      126. p1 p2
      127. hda: max request size: 1024KiB
      128. select 0
      129. hda: 976773168 sectors (500107 MB) w/8192KiB Cache, CHS=60801/255/63, (U)DMA
      130. hda: cache flushes supported
      131. /dev/ide/host0/bus0/target0/lun0: p1
      132. adding dm7025 NAND !
      133. 2881 kb/s
      134. 6578 kb/s
      135. - NAND PROBE: ad 75 ad 75
      136. NAND device: Manufacturer ID: 0xad, Chip ID: 0x75 (Unknown NAND 32MiB 3,3V 8-bit)
      137. Scanning device for bad blocks
      138. Bad eraseblock 1125 at 0x01194000
      139. Bad eraseblock 1831 at 0x01c9c000
      140. Creating 4 MTD partitions on "NAND 32MiB 3,3V 8-bit":
      141. 0x00000000-0x02000000 : "complete"
      142. 0x00000000-0x00040000 : "loader"
      143. 0x00040000-0x00400000 : "boot partition"
      144. 0x00400000-0x02000000 : "root partition"
      145. usbmon: debugs is not available
      146. ohci_hcd 0000:00:14.2: PCI device 1002:4867 (ATI Technologies Inc)
      147. ohci_hcd 0000:00:14.2: new USB bus registered, assigned bus number 1
      148. ohci_hcd 0000:00:14.2: irq 2, io mem 0x10000000
      149. usb usb1: Product: PCI device 1002:4867 (ATI Technologies Inc)
      150. usb usb1: Manufacturer: Linux 2.6.12.6 ohci_hcd
      151. usb usb1: SerialNumber: 0000:00:14.2
      152. hub 1-0:1.0: USB hub found
      153. hub 1-0:1.0: 2 ports detected
      154. Initializing USB Mass Storage driver...
      155. usbcore: registered new driver usb-storage
      156. USB Mass Storage support registered.
      157. usb 1-1: new full speed USB device using ohci_hcd and address 2
      158. usb 1-1: Product: USB2.0 WLAN
      159. usb 1-1: Manufacturer: ZyDAS
      160. usbcore: registered new driver usbhid
      161. drivers/usb/input/hid-core.c: v2.01:USB HID core driver
      162. usbcore: registered new driver usbserial
      163. drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
      164. i2c /dev entries driver
      165. Advanced Linux Sound Architecture Driver Version 1.0.9rc2 (Thu Mar 24 10:33:39 2005 UTC).
      166. ALSA device list:
      167. No soundcards found.
      168. NET: Registered protocol family 2
      169. IP: routing cache hash table of 512 buckets, 4Kbytes
      170. TCP established hash table entries: 4096 (order: 3, 32768 bytes)
      171. TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
      172. TCP: Hash tables configured (established 4096 bind 4096)
      173. NET: Registered protocol family 1
      174. NET: Registered protocol family 17
      175. select 1
      176. kjournald starting. Commit interval 5 seconds
      177. EXT3 FS on hdc2, internal journal
      178. EXT3-fs: recovery complete.
      179. EXT3-fs: mounted filesystem with ordered data mode.
      180. VFS: Mounted root (ext3 filesystem).
      181. Freeing unused kernel memory: 124k freed
      183. INIT: version 2.86 booting
      185. stb_core: module license 'Proprietary' taints kernel.
      186. read CA...
      187. CA dump:
      188. 01 01 03
      189. 02 01 04
      190. 03 04 00 00 a0 71
      191. 04 06 00 09 34 1c 3c 78
      192. 09 02 01 01
      193. 06 08 32 30 30 39 30 39 31 34
      194. 07 0f 39 39 31 34 30 33 30 34 30 30 34 31 30 37 33
      195. 08 01 01
      196. ff 01 8e
      197. read DCA...dCA: not existent
      198. error
      199. lcd.o: LCD driver (KS0713) module
      200. OLED detected.
      201. scale_brightness: 12
      202. 4000792 ms:
      203. 86 ms: 28 Starting /etc/rcS.d/S02sysfs...
      204. 19 ms: =s
      205. 28 ms: 31 Starting /etc/rcS.d/S04bootup...
      206. devfsd v1.3.25 started for /dev
      207. mknod: /dev/hda: File exists
      208. mknod: /dev/hda1: File exists
      209. mknod: /dev/hdc: File exists
      210. mknod: /dev/hdc1: File exists
      211. mknod: /dev/hdc2: File exists
      212. 713 ms: 4
      213. 41 ms: 10
      214. select 0
      215. kjournald starting. Commit interval 5 seconds
      216. EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
      217. EXT3 FS on hda1, internal journal
      218. EXT3-fs: recovery complete.
      219. EXT3-fs: mounted filesystem with ordered data mode.
      220. select 1
      221. 129 ms: 11
      222. 1127 ms: 12
      223. stv6412_detect:24: before transfer: i2c=c0132180 addr=74 msg=81335d7c buf=81335d78
      224. stv6412_detect:28: fail
      225. set sb to 3(2)
      226. set fb to 2(-1)
      227. set fb to 2(0)
      228. set input to 0
      229. set sb to 3(2)
      230. set fb to 2(0)
      231. no bootloader defined videomode found, using CVBS...
      232. no bootloader defined videomode found, using PAL...
      233. SYNC: old: 0 -> new: 1 (requested: 3)
      234. SYNC: old: 0 -> new: 1 (requested: 3)
      235. audio_j1_streamtype_set(0)
      236. init ALSA!
      237. Write AVS: 40 00 40 40 00 00 00 03 00 02 00 03 03 3f
      238. Write AVS: 40 00 40 40 00 00 18 63 00 02 00 03 03 3f
      239. tsmux write 20
      240. tsmux write 20
      241. tsmux write 20
      242. card init
      243. autodetecting NIMs...
      244. CI removed...
      245. Found: Slot A, addr 42, ID: 05 (by CA)
      246. Resetting Slot A
      247. Found: Slot B, addr 42, ID: 05 (by CA)
      248. Resetting Slot B
      249. DVB: registering new adapter (xilleon).
      250. DVB: registering frontend 0 (ALPS-BSBE1-C/D01A DVB-S (STV0288))...
      251. DVB: registering frontend 0 (ALPS-BSBE1-C/D01A DVB-S (STV0288))...
      252. usbcore: registered new driver rt73
      254. _____ ____ _ ____
      255. |__ / _| _ \ / \ / ___|
      256. / / | | | | | |/ _ \ \___ \
      257. / /| |_| | |_| / ___ \ ___) |
      258. /____\__, |____/_/ \_\____/
      259. |___/
      260. ZD1211B - version 2.22.0.0-development
      261. vendor_id = 0ace
      262. product_id = 1215
      263. USB 1.1 Host
      264. Release Ver = 4810
      265. EEPORM Ver = 4810
      266. Finsih download Firmware. Ready to reboot
      Alles anzeigen


      Kann seine daß die

      Quellcode

      1. console=ttyS0,115200 root=/dev/mtdblock2 rootfstype=jffs2 ro
      nicht die cf abfrägt? :denk:

      LG
      kostar

      Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von kostar ()

    • Ja das müsste /dev/hda2 /dev/hdb2 sein

      Quellcode

      1. console=ttyS0,115200 root=/dev/hda2 rootfstype=ext3 rw



      Quellcode

      1. console=ttyS0,115200 root=/dev/hdb2 rootfstype=ext3 rw


      Wenn eine Festplatte eingebaut ist dann eher die zweite Zeile.

    • jetzt bootet gar nicht...

      habe beide Zeilen probiert,

      log Meldung:

      Quellcode

      1. VFS: Unable to mount root fs via NFS, trying floppy.
      2. VFS: Cannot open root device "hdb1" or unknown-block(2,0)
      3. Please append a correct "root=" boot option
      4. Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0)

      Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von kostar ()

    • Hallo,
      also mit factory settings ins BIOS konnte ich folgende bootöog erzeugen:

      Brainfuck-Quellcode

      1. =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.11.25 17:58:22 =~=~=~=~=~=~=~=~=~=~=~=
      2. Rebooting... select 0
      3. Restarting system.
      4. fp_restart
      5. *
      6. Dreambox D M7025FIRST STAGE 1.4 {2345}
      7. [m2ND STAGE OK, build #83 (2011-02-28)
      9. 0.000 - DM7025 board setup
      10. 0.002 - initializing PCI...
      11. 0.012 - done!
      12. 0.014 - fp init
      13. FP version 7 detected
      14. 0.101 - ca init
      15. RSA key 1 is used.
      16. 0.206 - load config
      17. dCA: not existent, loading defaults
      18. 0.788 - config loaded.
      19. * press [S] to enter setup
      20. 7831152 sectors (3823 MB)
      21. P 06 1 10079 < 7831152
      22. OLED found!
      23. lcd: BOOT #83
      24. - read config file: /boot/secondstage.conf
      25. detected jffs2 blocksize: 16kb
      26. +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
      27. +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
      28. +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
      29. +++++++++++++++++++++++++++++++++++++++++++++++++++
      30. dreamupd initialized
      31. Scanning JFFS2 FS: . | / - \ | / - \ | / - \ | / done.find_inode failed for name=secondstage.confload: Failed to find inode - failed to open /boot/secondstage.conf
      32. lcd: CF AVAILABLE
      33. +CF
      35. Device 2: Partition 1: Filesystem: FAT32 "BOOTFS"
      36. lcd: /cf/bootlogo.elf
      37. bootlogo size: 49877
      38. vscale: 576:576
      39. lcd: /cf/vmlinux.gz
      41. LINUX started...
      42. ATI Xilleon 226 (little endian), Solo mode
      43. PCI bus speed is 33MHz
      44. Initializing IRQs
      45. about to enable interrupts!
      46. interrupts enabled.
      47. Linux version 2.6.12.6 (newnigma2@vs35) (gcc version 4.4.3 (GCC) ) #1 Tue Feb 8 07:31:50 UTC 2011
      48. memsize: 77MB
      49. Xilleon REG value before setting: PAD_USB1: 0xf43, PAD_USB2: 0xf43
      50. Xilleon REG value after setting: PAD_USB1: 0xf43, PAD_USB2: 0xf43
      51. CPU revision is: 00018448
      52. Determined physical RAM map:
      53. memory: 00080000 @ 00000000 (ROM data)
      54. memory: 00080000 @ 00080000 (reserved)
      55. memory: 04c00000 @ 00100000 (usable)
      56. Built 1 zonelists
      57. Kernel command line: root=/dev/hdc2 rootfstype=ext3 console=ttyS0,115200 rw
      58. Primary instruction cache 16kB, physically tagged, 4-way, linesize 16 bytes.
      59. Primary data cache 16kB, 4-way, linesize 16 bytes.
      60. Synthesized TLB refill handler (20 instructions).
      61. Synthesized TLB load handler fastpath (32 instructions).
      62. Synthesized TLB store handler fastpath (32 instructions).
      63. Synthesized TLB modify handler fastpath (31 instructions).
      64. PID hash table entries: 512 (order: 9, 8192 bytes)
      65. calculating r4koff... CPU frequency 299.68 MHz
      66. Using 149.838 MHz high precision timer.
      67. Console: colour dummy device 80x25
      68. Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
      69. Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
      70. Memory: 72960k/77824k available (2862k kernel code, 4700k reserved, 813k data, 124k init, 0k highmem)
      71. Mount-cache hash table entries: 512
      72. Checking for 'wait' instruction... available.
      73. NET: Registered protocol family 16
      74. Can't analyze prologue code at 803c9990
      75. PCI init - ohwe, ohwe..
      76. SCSI subsystem initialized
      77. usbcore: registered new driver usbfs
      78. usbcore: registered new driver hub
      79. irq fixup slot 10 vendor 10ec irq 33
      80. TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
      81. inotify device minor=63
      82. devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
      83. devfs: boot_options: 0x0
      84. JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
      85. Initializing Cryptographic API
      86. Serial: 8250/16550 driver $Revision: 1.90 $ 6 ports, IRQ sharing disabled
      87. ttyS0 at MMIO 0x0 (irq = 100) is a 16550A
      88. ttyS1 at MMIO 0x0 (irq = 99) is a 16550A
      89. io scheduler noop registered
      90. io scheduler anticipatory registered
      91. io scheduler deadline registered
      92. io scheduler cfq registered
      93. 8139too Fast Ethernet driver 0.9.27
      94. RTL8139 EEPROM CONTENT: 8129 10ec 8139 10ec 8139 2020 e512 0900 0034 0000
      95. eth0: RealTek RTL8139 at 0x2000, 00:09:34:1c:3c:78, IRQ 33
      96. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
      97. ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
      98. X226: IDE controller at PCI slot 0000:00:14.1
      99. X226: chipset revision 1
      100. X226: 100% native mode on irq 3
      101. hwif->channel: 0, hwif->index: 0
      102. ide0: BM-DMA at 0x2400-0x2407, BIOS settings: hda:DMA, hdb:DMA
      103. init_hwif_xilleon, 0, mate: 00000000
      104. hwif->channel: 0, hwif->index: 1
      105. ide1: BM-DMA at 0x2400-0x2407, BIOS settings: hdc:DMA, hdd:DMA
      106. init_hwif_xilleon, 1, mate: 804ce0d8
      107. select 1
      108. hdc: TS4GCF133, ATA DISK drive
      109. hdc: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
      110. hdc: set_drive_speed_status: error=0x04 { DriveStatusError }
      111. ide1 at 0x2410-0x2417,0x2422 on irq 3
      112. select 0
      113. hda: WDC WD5000AVJB-63J1A0, ATA DISK drive
      114. ide0 at 0x2410-0x2417,0x2422 on irq 3 (shared with ide1)
      115. hdc: max request size: 128KiB
      116. hdc: 7831152 sectors (4009 MB) w/1KiB Cache, CHS=7769/16/63
      117. hdc: cache flushes not supported
      118. /dev/ide/host1/bus0/target0/lun0:select 1
      119. p1 p2
      120. hda: max request size: 1024KiB
      121. select 0
      122. hda: 976773168 sectors (500107 MB) w/8192KiB Cache, CHS=60801/255/63, (U)DMA
      123. hda: cache flushes supported
      124. /dev/ide/host0/bus0/target0/lun0: p1
      125. adding dm7025 NAND !
      126. 2873 kb/s
      127. 6535 kb/s
      128. - NAND PROBE: ad 75 ad 75
      129. NAND device: Manufacturer ID: 0xad, Chip ID: 0x75 (Unknown NAND 32MiB 3,3V 8-bit)
      130. Scanning device for bad blocks
      131. Bad eraseblock 1125 at 0x01194000
      132. Bad eraseblock 1831 at 0x01c9c000
      133. Creating 4 MTD partitions on "NAND 32MiB 3,3V 8-bit":
      134. 0x00000000-0x02000000 : "complete"
      135. 0x00000000-0x00040000 : "loader"
      136. 0x00040000-0x00400000 : "boot partition"
      137. 0x00400000-0x02000000 : "root partition"
      138. usbmon: debugs is not available
      139. ohci_hcd 0000:00:14.2: PCI device 1002:4867 (ATI Technologies Inc)
      Alles anzeigen


      fast 20minuten lang hat´s an der zeile: 130

      Scanning device for bad blocks
      hilft´s?
      hat jemand eine Idee?

      Grüße
      kostar

      Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von kostar ()

    • Kernel command line: root=/dev/hdc2 rootfstype=ext3 console=ttyS0,115200 rw


      Also ist auch noch ein 3. Laufwerk angeschlossen.
      Ja sorry da habe ich vorhin nicht ganz aufgepasst, versuche es mal mit:

      Quellcode

      1. rootdelay=15 root=/dev/hdc2 rootfstype=ext3 rw console=ttyS0,115200 init=/sbin/init

    • Original von sparksofinsanity
      Kernel command line: root=/dev/hdc2 rootfstype=ext3 console=ttyS0,115200 rw


      Also ist auch noch ein 3. Laufwerk angeschlossen.
      Ja sorry da habe ich vorhin nicht ganz aufgepasst, versuche es mal mit:

      Quellcode

      1. rootdelay=15 root=/dev/hdc2 rootfstype=ext3 rw console=ttyS0,115200 init=/sbin/init


      Leider hat auch so nicht funktioniert.

      ich habe folgende command probiert:

      Quellcode

      1. console=ttyS0,115200 root=/dev/hdc2 rootfstype=ext3 ro


      und habe folgende bootlog bekommen:

      Brainfuck-Quellcode

      1. =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.11.25 20:39:19 =~=~=~=~=~=~=~=~=~=~=~=
      2. *
      3. Dreambox D M7025
      5. FIRST STAGE 1.4 {2345}
      6. [m
      8. 2ND STAGE OK, build #83 (2011-02-28)
      10. 0.000 - DM7025 board setup
      11. 0.002 - initializing PCI...
      12. 0.012 - done!
      13. 0.014 - fp init
      14. FP version 7 detected
      15. 0.160 - ca init
      16. RSA key 1 is used.
      17. 0.264 - load config
      18. 0.844 - config loaded.
      19. * press [S] to enter setup
      20. 7831152 sectors (3823 MB)
      21. P 06 1 10079 < 7831152
      22. OLED found!
      23. lcd: BOOT #83
      24. - read config file: /boot/secondstage.conf
      25. detected jffs2 blocksize: 16kb
      26. +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
      27. +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
      28. +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
      29. +++++++++++++++++++++++++++++++++++++++++++++++++++
      30. dreamupd initialized
      31. Scanning JFFS2 FS: . | / - \ | / - \ | / - \ | / done.
      33. find_inode failed for name=secondstage.conf
      35. load: Failed to find inode
      37. - failed to open /boot/secondstage.conf
      38. lcd: CF AVAILABLE
      39. +CF
      41. Device 2: Partition 1: Filesystem: FAT32 "BOOTFS"
      42. lcd: /cf/bootlogo.elf
      43. bootlogo size: 49877
      44. vscale: 576:576
      45. lcd: /cf/vmlinux.gz
      47. LINUX started...
      48. ATI Xilleon 226 (little endian), Solo mode
      49. PCI bus speed is 33MHz
      50. Initializing IRQs
      51. about to enable interrupts!
      52. interrupts enabled.
      53. Linux version 2.6.12.6 (newnigma2@vs35) (gcc version 4.4.3 (GCC) ) #1 Tue Feb 8 07:31:50 UTC 2011
      54. memsize: 77MB
      55. Xilleon REG value before setting: PAD_USB1: 0xf43, PAD_USB2: 0xf43
      56. Xilleon REG value after setting: PAD_USB1: 0xf43, PAD_USB2: 0xf43
      57. CPU revision is: 00018448
      58. Determined physical RAM map:
      59. memory: 00080000 @ 00000000 (ROM data)
      60. memory: 00080000 @ 00080000 (reserved)
      61. memory: 04c00000 @ 00100000 (usable)
      62. Built 1 zonelists
      63. Kernel command line: console=ttyS0,115200 root=/dev/hdc2 rootfstype=ext3 rw
      64. Primary instruction cache 16kB, physically tagged, 4-way, linesize 16 bytes.
      65. Primary data cache 16kB, 4-way, linesize 16 bytes.
      66. Synthesized TLB refill handler (20 instructions).
      67. Synthesized TLB load handler fastpath (32 instructions).
      68. Synthesized TLB store handler fastpath (32 instructions).
      69. Synthesized TLB modify handler fastpath (31 instructions).
      70. PID hash table entries: 512 (order: 9, 8192 bytes)
      71. calculating r4koff... CPU frequency 299.68 MHz
      72. Using 149.838 MHz high precision timer.
      73. Console: colour dummy device 80x25
      74. Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
      75. Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
      76. Memory: 72960k/77824k available (2862k kernel code, 4700k reserved, 813k data, 124k init, 0k highmem)
      77. Mount-cache hash table entries: 512
      78. Checking for 'wait' instruction... available.
      79. NET: Registered protocol family 16
      80. Can't analyze prologue code at 803c9990
      81. PCI init - ohwe, ohwe..
      82. SCSI subsystem initialized
      83. usbcore: registered new driver usbfs
      84. usbcore: registered new driver hub
      85. irq fixup slot 10 vendor 10ec irq 33
      86. TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
      87. inotify device minor=63
      88. devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
      89. devfs: boot_options: 0x0
      90. JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
      91. Initializing Cryptographic API
      92. Serial: 8250/16550 driver $Revision: 1.90 $ 6 ports, IRQ sharing disabled
      93. ttyS0 at MMIO 0x0 (irq = 100) is a 16550A
      94. ttyS1 at MMIO 0x0 (irq = 99) is a 16550A
      95. io scheduler noop registered
      96. io scheduler anticipatory registered
      97. io scheduler deadline registered
      98. io scheduler cfq registered
      99. 8139too Fast Ethernet driver 0.9.27
      100. RTL8139 EEPROM CONTENT: 8129 10ec 8139 10ec 8139 2020 e512 0900 0034 0000
      101. eth0: RealTek RTL8139 at 0x2000, 00:09:34:1c:3c:78, IRQ 33
      102. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
      103. ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
      104. X226: IDE controller at PCI slot 0000:00:14.1
      105. X226: chipset revision 1
      106. X226: 100% native mode on irq 3
      107. hwif->channel: 0, hwif->index: 0
      108. ide0: BM-DMA at 0x2400-0x2407, BIOS settings: hda:DMA, hdb:DMA
      109. init_hwif_xilleon, 0, mate: 00000000
      110. hwif->channel: 0, hwif->index: 1
      111. ide1: BM-DMA at 0x2400-0x2407, BIOS settings: hdc:DMA, hdd:DMA
      112. init_hwif_xilleon, 1, mate: 804ce0d8
      113. select 1
      114. hdc: TS4GCF133, ATA DISK drive
      115. hdc: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
      116. hdc: set_drive_speed_status: error=0x04 { DriveStatusError }
      117. ide1 at 0x2410-0x2417,0x2422 on irq 3
      118. select 0
      119. hda: WDC WD5000AVJB-63J1A0, ATA DISK drive
      120. ide0 at 0x2410-0x2417,0x2422 on irq 3 (shared with ide1)
      121. hdc: max request size: 128KiB
      122. hdc: 7831152 sectors (4009 MB) w/1KiB Cache, CHS=7769/16/63
      123. hdc: cache flushes not supported
      124. /dev/ide/host1/bus0/target0/lun0:select 1
      125. p1 p2
      126. hda: max request size: 1024KiB
      127. select 0
      128. hda: 976773168 sectors (500107 MB) w/8192KiB Cache, CHS=60801/255/63, (U)DMA
      129. hda: cache flushes supported
      130. /dev/ide/host0/bus0/target0/lun0: p1
      131. adding dm7025 NAND !
      132. 2873 kb/s
      133. 6535 kb/s
      134. - NAND PROBE: ad 75 ad 75
      135. NAND device: Manufacturer ID: 0xad, Chip ID: 0x75 (Unknown NAND 32MiB 3,3V 8-bit)
      136. Scanning device for bad blocks
      137. Bad eraseblock 1125 at 0x01194000
      138. Bad eraseblock 1831 at 0x01c9c000
      139. Creating 4 MTD partitions on "NAND 32MiB 3,3V 8-bit":
      140. 0x00000000-0x02000000 : "complete"
      141. 0x00000000-0x00040000 : "loader"
      142. 0x00040000-0x00400000 : "boot partition"
      143. 0x00400000-0x02000000 : "root partition"
      144. usbmon: debugs is not available
      145. ohci_hcd 0000:00:14.2: PCI device 1002:4867 (ATI Technologies Inc)
      146. ohci_hcd 0000:00:14.2: new USB bus registered, assigned bus number 1
      147. ohci_hcd 0000:00:14.2: irq 2, io mem 0x10000000
      148. usb usb1: Product: PCI device 1002:4867 (ATI Technologies Inc)
      149. usb usb1: Manufacturer: Linux 2.6.12.6 ohci_hcd
      150. usb usb1: SerialNumber: 0000:00:14.2
      151. hub 1-0:1.0: USB hub found
      152. hub 1-0:1.0: 2 ports detected
      153. Initializing USB Mass Storage driver...
      154. usbcore: registered new driver usb-storage
      155. USB Mass Storage support registered.
      156. usb 1-1: new full speed USB device using ohci_hcd and address 2
      157. usb 1-1: Product: USB2.0 WLAN
      158. usb 1-1: Manufacturer: ZyDAS
      159. usbcore: registered new driver usbhid
      160. drivers/usb/input/hid-core.c: v2.01:USB HID core driver
      161. usbcore: registered new driver usbserial
      162. drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
      163. i2c /dev entries driver
      164. Advanced Linux Sound Architecture Driver Version 1.0.9rc2 (Thu Mar 24 10:33:39 2005 UTC).
      165. ALSA device list:
      166. No soundcards found.
      167. NET: Registered protocol family 2
      168. IP: routing cache hash table of 512 buckets, 4Kbytes
      169. TCP established hash table entries: 4096 (order: 3, 32768 bytes)
      170. TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
      171. TCP: Hash tables configured (established 4096 bind 4096)
      172. NET: Registered protocol family 1
      173. NET: Registered protocol family 17
      174. select 1
      175. kjournald starting. Commit interval 5 seconds
      176. EXT3 FS on hdc2, internal journal
      177. EXT3-fs: recovery complete.
      178. EXT3-fs: mounted filesystem with ordered data mode.
      179. VFS: Mounted root (ext3 filesystem).
      180. Freeing unused kernel memory: 124k freed
      182. INIT: version 2.86 booting
      184. stb_core: module license 'Proprietary' taints kernel.
      185. read CA...
      186. CA dump:
      187. 01 01 03
      188. 02 01 04
      189. 03 04 00 00 a0 71
      190. 04 06 00 09 34 1c 3c 78
      191. 09 02 01 01
      192. 06 08 32 30 30 39 30 39 31 34
      193. 07 0f 39 39 31 34 30 33 30 34 30 30 34 31 30 37 33
      194. 08 01 01
      195. ff 01 8e
      196. read DCA...ok
      197. lcd.o: LCD driver (KS0713) module
      198. OLED detected.
      199. scale_brightness: 12
      200. 4009331 ms:
      201. 86 ms: 28 Starting /etc/rcS.d/S02sysfs...
      202. 19 ms: =s
      203. 29 ms: 31 Starting /etc/rcS.d/S04bootup...
      204. devfsd v1.3.25 started for /dev
      205. mknod: /dev/hda: File exists
      206. mknod: /dev/hda1: File exists
      207. mknod: /dev/hdc: File exists
      208. mknod: /dev/hdc1: File exists
      209. mknod: /dev/hdc2: File exists
      210. 721 ms: 4
      211. 41 ms: 10
      212. select 0
      213. kjournald starting. Commit interval 5 seconds
      214. EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
      215. EXT3 FS on hda1, internal journal
      216. EXT3-fs: recovery complete.
      217. EXT3-fs: mounted filesystem with ordered data mode.
      218. select 1
      219. 163 ms: 11
      220. 1129 ms: 12
      221. stv6412_detect:24: before transfer: i2c=c0132180 addr=74 msg=84995d7c buf=84995d78
      222. stv6412_detect:28: fail
      223. set sb to 3(2)
      224. set fb to 2(-1)
      225. set fb to 2(0)
      226. set input to 0
      227. set sb to 3(2)
      228. set fb to 2(0)
      229. found bootloader defined colorformat: 0
      230. found bootloader defined videomode: 0
      231. SYNC: old: 0 -> new: 1 (requested: 3)
      232. SYNC: old: 0 -> new: 1 (requested: 3)
      233. audio_j1_streamtype_set(0)
      234. init ALSA!
      235. Write AVS: 40 00 40 40 00 00 00 03 00 02 00 03 03 3f
      236. Write AVS: 40 00 40 40 00 00 18 63 00 02 00 03 03 3f
      237. tsmux write 20
      238. tsmux write 20
      239. tsmux write 20
      240. card init
      241. autodetecting NIMs...
      242. CI removed...
      243. Found: Slot A, addr 42, ID: 05 (by CA)
      244. Resetting Slot A
      245. Found: Slot B, addr 42, ID: 05 (by CA)
      246. Resetting Slot B
      247. DVB: registering new adapter (xilleon).
      248. DVB: registering frontend 0 (ALPS-BSBE1-C/D01A DVB-S (STV0288))...
      249. DVB: registering frontend 0 (ALPS-BSBE1-C/D01A DVB-S (STV0288))...
      250. usbcore: registered new driver rt73
      252. _____ ____ _ ____
      253. |__ / _| _ \ / \ / ___|
      254. / / | | | | | |/ _ \ \___ \
      255. / /| |_| | |_| / ___ \ ___) |
      256. /____\__, |____/_/ \_\____/
      257. |___/
      258. ZD1211B - version 2.22.0.0-development
      259. vendor_id = 0ace
      260. product_id = 1215
      261. USB 1.1 Host
      262. Release Ver = 4810
      263. EEPORM Ver = 4810
      264. Finsih download Firmware. Ready to reboot
      Alles anzeigen


      jetzt bleibt für ca 20min stehen.


      MFG
      kostar

    • console=ttyS0,115200 root=/dev/hdc2 rootfstype=ext3 ro


      Naja wenn du das root Filesystem read only mountest dann bootet die Box eh nicht richtig.
      Die Box scheint aber eher zufällig zu stehen .. ich kann da bis jetzt kein Muster ausmachen.

      2x hing sie nach dem Zydas WLAN Treiber und 1x wesentlich früher.

    • ja, eigentlich ob die "command line" enabled oder disabled ist, macht gar nichts aus...

      die bootlogs sehen alle genauso aus, gleich na dem "Zydas" bleibt stehen. Eigentlich habe mittlerweile mehrere gleiche bootlogs, einfach habe ich nicht alle gepostet. Das bootlog mit dem "hänger" beim scannen war die Ausnahme!

      und so geht´s weiter nach ca.15 min Pause:

      Quellcode

      1. PA type: 0
      2. PHYNEWLayout = 1
      3. Airoha AL2230S_RF
      4. AllowedChannel = 000107ff
      5. Region:48
      6. usbcore: registered new driver zd1211b
      7. usbcore: registered new driver r871x_usb_drv
      8. modprobe: module rt3070 not found in modules.dep
      9. modprobe: module ftdi_sio not found in modules.dep
      10. modprobe: module pl2303 not found in modules.dep
      11. modprobe: module info not found in modules.dep
      12. modprobe: module ipv6 not found in modules.dep
      13. modprobe: module nfsd not found in modules.dep
      14. modprobe: module autofs4 not found in modules.dep
      15. modprobe: module vfat not found in modules.dep
      16. fuse init (API version 7.8)
      17. fuse distribution version: 2.7.6
      18. modprobe: module tun not found in modules.dep
      19. modprobe: module hfs not found in modules.dep
      20. modprobe: module hfsplus not found in modules.dep
      21. 1002680 ms: 13
      22. 41 ms: 15
      24. /dev/hda:
      25. setting acousselect 0
      26. tic management to 128
      27. acoustic = 128 (128=quiet ... 254=fast)
      29. usw,usw.....
      Alles anzeigen


      komisch ist aber, ich hab die gleiche bootzeiten auf zwei boxen und nur wenn´s vom cf geht...

    • Gute Idee!
      Also ohne den Stick bootet super schnell :D
      aber...,
      ohne wlan komme ich nicht zu Router :rolleyes:

      Was mich aber stützig macht, ist wie kann der gleiche Treiber übers flash problemlos laufen und schnell booten und übers cf, braucht eine kleine ewigkeit?? :denk: :denk:

    • Naja die Zusammenhänge können schon etwas komplexer sein, ist der CF Reader über USB eingebunden ? ;)

      Da muss ich leider passen, ich habe noch nie eine 7025 gehabt und werde mir auch keine mehr anschaffen - da das Gerät nicht auf dem Stand der aktuellen Technik ist.

    • Original von kostar
      Gute Idee!
      Also ohne den Stick bootet super schnell :D
      aber...,
      ohne wlan komme ich nicht zu Router :rolleyes:


      Unelegante aber wirksame Lösung:):
      Nimm ne WLan Bridge und klemm die an den ethernet port, hatte ich auch mal als Lösung, als ich Probleme mit einem Wlan stick hatte.

    • nööö! :)

      ich habe zwar ein Bridge, die ist aber mit meinem dm600 verbunden ;)
      Bei der Lösung, stimmt´s daß eigentlich nicht die eleganteste ist aber,

      man kann ohne wifi stick neustarten, dann wifi einstecken und dann reicht´s bloß ein Enigma Neustart. ;)
      habe probiert und läuft!!

      Danke!!

      MFG
      kostar