Iperf NN fähig ?

    Diese Seite verwendet Cookies. Durch die Nutzung unserer Seite erklären Sie sich damit einverstanden, dass wir Cookies setzen. Weitere Informationen

    • Iperf NN fähig ?

      Hi gibt es auch eine Version von Iperf, die unter NN 4.x.x läuft. Bzw. OE 2.0
      Danke
      EDIT
      Manuel lässt es sich installieren.
      Läuft auch.

      und bestätigt meine wahrgenommene Trägheit.

      An was kann das liegen, dass es gar so grottig langsam ist.

      ------------------------------------------------------------
      [ 3] local 192.168.178.2 port 52444 connected with 192.168.178.8 port 5001
      [ ID] Interval Transfer Bandwidth
      [ 3] 0.0-10.0 sec 1.25 MBytes 1.05 Mbits/sec
      [ 3] Sent 893 datagrams
      [ 3] WARNING: did not receive ack of last datagram after 10 tries.

      Dieser Beitrag wurde bereits 2 mal editiert, zuletzt von Badly ()

    • liegt auf dem unstable feed


      opkg update
      opkg install iperf
      Installing iperf (2.0.4-r0) to flash...
      Downloading feed.newnigma2.to/unstable/4.0…erf_2.0.4-r0_mips32el.ipk.
      Configuring iperf.

      root@dm800sev2:~# iperf -h
      Usage: iperf [-s|-c host] [options]
      iperf [-h|--help] [-v|--version]

      Client/Server:
      -f, --format [kmKM] format to report: Kbits, Mbits, KBytes, MBytes
      -i, --interval # seconds between periodic bandwidth reports
      -l, --len #[KM] length of buffer to read or write (default 8 KB)
      -m, --print_mss print TCP maximum segment size (MTU - TCP/IP header)
      -o, --output <filename> output the report or error message to this specified file
      -p, --port # server port to listen on/connect to
      -u, --udp use UDP rather than TCP
      -w, --window #[KM] TCP window size (socket buffer size)
      -B, --bind <host> bind to <host>, an interface or multicast address
      -C, --compatibility for use with older versions does not sent extra msgs
      -M, --mss # set TCP maximum segment size (MTU - 40 bytes)
      -N, --nodelay set TCP no delay, disabling Nagle's Algorithm
      -V, --IPv6Version Set the domain to IPv6

      Server specific:
      -s, --server run in server mode
      -U, --single_udp run in single threaded UDP mode
      -D, --daemon run the server as a daemon

      Client specific:
      -b, --bandwidth #[KM] for UDP, bandwidth to send at in bits/sec
      (default 1 Mbit/sec, implies -u)
      -c, --client <host> run in client mode, connecting to <host>
      -d, --dualtest Do a bidirectional test simultaneously
      -n, --num #[KM] number of bytes to transmit (instead of -t)
      -r, --tradeoff Do a bidirectional test individually
      -t, --time # time in seconds to transmit for (default 10 secs)
      -F, --fileinput <name> input the data to be transmitted from a file
      -I, --stdin input the data to be transmitted from stdin
      -L, --listenport # port to recieve bidirectional tests back on
      -P, --parallel # number of parallel client threads to run
      -T, --ttl # time-to-live, for multicast (default 1)
      -Z, --linux-congestion <algo> set TCP congestion control algorithm (Linux only)

      Miscellaneous:
      -x, --reportexclude [CDMSV] exclude C(connection) D(data) M(multicast) S(settings) V(server) reports
      -y, --reportstyle C report as a Comma-Separated Values
      -h, --help print this message and quit
      -v, --version print version information and quit

      [KM] Indicates options that support a K or M suffix for kilo- or mega-

      The TCP window size option can be set by the environment variable
      TCP_WINDOW_SIZE. Most other options can be set by an environment variable
      IPERF_<long option name>, such as IPERF_BANDWIDTH.

      Report bugs to <iperf-users@lists.sourceforge.net>
      » time to say goodbye «

      Konfuzius sagt:
      Erst wenn eine Mücke auf deinen Hoden landet wirst du lernen Probleme ohne Gewalt zu lösen.
    • WLAN oder LAN? Wie sieht dein Netzwerk aus? "Es ist langsam" ist etwas wenig Info ....

      meine DM72020HD im Gbit-LAN Netz:

      Brainfuck-Quellcode

      1. root@dm7020hd:~# iperf -c 192.168.100.100
      2. ------------------------------------------------------------
      3. Client connecting to 192.168.100.100, TCP port 5001
      4. TCP window size: 20.7 KByte (default)
      5. ------------------------------------------------------------
      6. [ 3] local 192.168.100.94 port 39486 connected with 192.168.100.100 port 5001
      7. [ ID] Interval Transfer Bandwidth
      8. [ 3] 0.0-10.0 sec 113 MBytes 94.4 Mbits/sec
      9. root@dm7020hd:~#
    • das ganze läuft per wlan.
      habe einen 300 mbit usb stick dran. läuft alles einwandfrei. aber wenn ich daten von oder auf die DM kopieren will, bewegt sich das ganze immer im 1MB /s bereich.
      Das interne wlan weist die gleichen werte auf.
      das ganze läuft über die 7141 fritzbox.
      Hardware DM 8000

      EDIT
      Wenn ich den Befehl ohne -u eingebe kommt
      [ 5] local 192.168.178.8 port 5001 connected with 192.168.178.2 port 35053
      [ 5] 0.0-10.1 sec 13.4 MBytes 11.1 Mbits/sec

      Trotzdem packt FTP nicht mal die 2MB - Marke

      Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von Badly ()

    • die box ist schon fast "Ur-"alt ...

      ich würde aber mal anderen WLAN Kanal probieren,
      mittlerweile sind die kanäle alle recht "überfüllt" da jeder wlan hat.

      test einfach mal einen kanal, den es in deiner umgebung nicht so oft gibt
      Probleme kann man niemals mit derselben Denkweise lösen.

      ¯\_(ツ)_/¯

      "Die Deutsche Rechtschreibung ist Freeware, sprich, du kannst sie kostenlos nutzen.
      Allerdings ist sie nicht Open Source, d.h. du darfst sie nicht verändern oder in veränderter Form veröffentlichen."
    • HAbe hier noch eine 7390 rumstehen.
      Dort siehts nicht viel rosiger aus. Trotz 300 MBIT Verbindung.
      [ 3] local 192.168.178.27 port 44071 connected with 192.168.178.2 port 5001
      [ 3] 0.0-10.0 sec 25.8 MBytes 21.6 Mbits/sec

      per FTP sind das knapp 4,5MB...ganz schön LAHM :SOS:
    • zufällig habe ich beide wnce hier rumstehen.
      was auch noch echt madig ist...
      der kopiervorgang auf die fritzbox nas bzw. dort auf die usb HDD
      300 Mbit laptop 300mbit router.
      per ftp schiebt der mit 3 MB pro sekunde
      WoWWWWWWWWW