DM 525 hängt sich beim Flash auf

    Diese Seite verwendet Cookies. Durch die Nutzung unserer Seite erklären Sie sich damit einverstanden, dass wir Cookies setzen. Weitere Informationen

    • Ich habe die 520er (Neue) Box nochmal geflasht. Aber diesmal mit USB Service Kabel mit COM Port via Putty.

      Fängt jemand was mit dem Output an ?

      Quellcode

      1. [ 542.700000] UBIFS: mounted UBI device 0, volume 0, name "dreambox-rootfs"
      2. [ 542.700000] UBIFS: file system size: 501428224 bytes (489676 KiB, 478 MiB, 3949 LEBs)
      3. [ 542.701000] UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEB s)
      4. [ 542.702000] UBIFS: media format: w4/r0 (latest is w4/r0)
      5. [ 542.703000] UBIFS: default compressor: lzo
      6. [ 542.703000] UBIFS: reserved for root: 0 bytes (0 KiB)
      7. [ 657.513000] UBIFS: un-mount UBI device 0, volume 0
      8. INIT: Switching to runlevel: 6
      9. INIT: Sending processes the TERM signal
      10. Stopping Dropbear SSH server: no /bin/true found; none killed
      11. Stopping autoflashd.
      12. Stopping recovery-ui.
      13. Stopping tpmd.
      14. Stopping internet superserver: xinetd.
      15. Unmounting remote filesystems...
      16. Stopping Lighttpd Web Server: stopped /usr/sbin/lighttpd (pid 364)
      17. lighttpd.
      18. Deconfiguring network interfaces... done.
      19. Sending all processes the TERM signal...
      20. Sending all processes the KILL signal...
      21. Deactivating swap...
      22. Unmounting local filesystems...
      23. Rebooting... [ 673.527000] Restarting system.
      24. Dreambox DM520
      25. M0CZS
      26. L2=1
      27. LLMB=1
      28. BrCfg=E30FB7C6
      29. #@
      30. BCM973625A0 CFE v15.3, Endian Mode: Little
      31. Build Date: Fri May 12 14:15:19 2017 (Jann@Cynric)
      32. Copyright (C) Broadcom Corporation.
      33. Non-CI box detected
      34. card if inited
      35. Enabling NAND flash at CS2: K9F4G08U0A(DEVICE ID=0xECDC1095), ECC Level=4, Spare Area Size=16
      36. MACRONIX SPI flash detected: Size = 16MB, Sector Size 4096, Page Size 256
      37. CPU speed: 751MHz
      38. DDR Frequency: 1061 MHz
      39. DDR Mode: DDR3
      40. Total memory(MEMC 0): 512MB
      41. MEMC 0 DDR Width: 16
      42. Boot Device: SPI
      43. Total flash: 16MB
      44. RTS VERSION: rts_hevc10_1067
      45. ETH0_PHY: INT
      46. ETH0_MDIO_MODE: 1
      47. ETH0_SPEED: 100
      48. ETH0_PHYADDR: 1
      49. init fp
      50. Initializing USB.
      51. CFE initialized.
      52. found card in unknown state
      53. ca valid!
      54. ***** DREAMBOX SSBL *****
      55. Not interrupted yet, trying autoboot or rescue loader, hit any key in the next 500ms to cancel
      56. Proceeding with autoboot.. You can try aborting with Ctrl+C
      57. Loader:elf Filesys:raw Dev:flash0.kernel File: Options:(null)
      58. Loading: 0x80001000/25503936 0x818538c0/235952 Entry address is 0x805cd1d0
      59. Closing network eth0
      60. Ethernet link is up: 100 Mbps Full-Duplex
      61. Starting program at 0x805cd1d0
      62. ▒[ 0.331000] console [ttyS0] enabled, bootconsole disabled
      63. [ 0.331000] console [ttyS0] enabled, bootconsole disabled
      64. [ 0.335000] loop: module loaded
      65. [ 0.336000] brcmstb_nand: NAND controller driver is loaded
      66. [ 0.336000] tun: Universal TUN/TAP device driver, 1.6
      67. [ 0.337000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
      68. [ 0.459000] bcmgenet: configuring instance #0 for internal PHY
      69. [ 0.479000] bcmgenet bcmgenet.0: (unregistered net_device): link down
      70. [ 0.480000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
      71. [ 0.481000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI
      72. [ 0.481000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
      73. [ 0.513000] ehci-brcm ehci-brcm.0: irq 66, io mem 0x10480300
      74. [ 0.519000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
      75. [ 0.520000] hub 1-0:1.0: USB hub found
      76. [ 0.520000] hub 1-0:1.0: 2 ports detected
      77. [ 0.521000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
      78. [ 0.522000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI
      79. [ 0.522000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 2
      80. [ 0.523000] ohci-brcm ohci-brcm.0: irq 67, io mem 0x10480400
      81. [ 0.589000] hub 2-0:1.0: USB hub found
      82. [ 0.589000] hub 2-0:1.0: 2 ports detected
      83. [ 0.590000] Initializing USB Mass Storage driver...
      84. [ 0.591000] usbcore: registered new interface driver usb-storage
      85. [ 0.592000] USB Mass Storage support registered.
      86. [ 0.592000] i2c /dev entries driver
      87. [ 0.593000] lirc_dev: IR Remote Control driver registered, major 253
      88. [ 0.593000] usbcore: registered new interface driver btusb
      89. [ 0.595000] TCP: cubic registered
      90. [ 0.595000] NET: Registered protocol family 10
      91. [ 0.597000] NET: Registered protocol family 17
      92. [ 0.597000] Bluetooth: RFCOMM TTY layer initialized
      93. [ 0.598000] Bluetooth: RFCOMM socket layer initialized
      94. [ 0.599000] Bluetooth: RFCOMM ver 1.11
      95. [ 0.599000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
      96. [ 0.600000] Bluetooth: BNEP filters: protocol multicast
      97. [ 0.600000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
      98. [ 0.601000] L2TP core driver, V2.0
      99. [ 0.601000] Registering the dns_resolver key type
      100. [ 0.602000] PM: CP0 COUNT/COMPARE frequency does not depend on divisor
      101. [ 0.604000] EBI CS2: setting up NAND flash (primary)
      102. [ 0.605000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit)
      103. [ 0.606000] brcmnand brcmnand.0: 512MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-4
      104. [ 0.606000]
      105. [ 0.609000] Bad block table found at page 261952, version 0x01
      106. [ 0.610000] brcmnand brcmnand.0: bitflips oob(80) data(1984) at 0x1ffe0000
      107. [ 0.611000] brcmnand brcmnand.0: uncorrectable error at 0x1ffe0600
      108. [ 0.613000] Bad block table found at page 261888, version 0x01
      109. [ 0.614000] nand_read_bbt: bad block at 0x000005780000
      110. [ 0.615000] nand_read_bbt: bad block at 0x0000057c0000
      111. [ 0.615000] nand_read_bbt: bad block at 0x000010180000
      112. [ 0.616000] nand_read_bbt: bad block at 0x0000101a0000
      113. [ 0.617000] nand_read_bbt: bad block at 0x00001ffc0000
      114. [ 0.617000] nand_read_bbt: bad block at 0x00001ffe0000
      115. [ 0.629000] Creating 3 MTD partitions on "brcmnand.0":
      116. [ 0.629000] 0x000000000000-0x00001f500000 : "rootfs"
      117. [ 0.632000] 0x000000000000-0x000020000000 : "entire_device"
      118. [ 0.634000] 0x00001f500000-0x00001fa00000 : "kernel"
      119. [ 0.635000] EBI CS0: setting up SPI flash
      120. [ 0.636000] spi_brcmstb spi_brcmstb.0: 1-lane output, 3-byte address
      121. [ 0.636000] spi_brcmstb spi_brcmstb.0: master is unqueued, this is deprecated
      122. [ 0.637000] m25p80 spi0.0: found mx25l12805d, expected w25q128bv
      123. [ 0.638000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
      124. [ 0.645000] UBI: attaching mtd0 to ubi0
      125. [ 0.646000] UBI: physical eraseblock size: 131072 bytes (128 KiB)
      126. [ 0.646000] UBI: logical eraseblock size: 126976 bytes
      127. [ 0.647000] UBI: smallest flash I/O unit: 2048
      128. [ 0.648000] UBI: VID header offset: 2048 (aligned 2048)
      129. [ 0.648000] UBI: data offset: 4096
      130. [ 3.794000] UBI: max. sequence number: 21088
      131. [ 3.810000] UBI: attached mtd0 to ubi0
      132. [ 3.811000] UBI: MTD device name: "rootfs"
      133. [ 3.812000] UBI: MTD device size: 501 MiB
      134. [ 3.812000] UBI: number of good PEBs: 4004
      135. [ 3.813000] UBI: number of bad PEBs: 4
      136. [ 3.813000] UBI: number of corrupted PEBs: 0
      137. [ 3.814000] UBI: max. allowed volumes: 128
      138. [ 3.814000] UBI: wear-leveling threshold: 4096
      139. [ 3.815000] UBI: number of internal volumes: 1
      140. [ 3.815000] UBI: number of user volumes: 1
      141. [ 3.816000] UBI: available PEBs: 0
      142. [ 3.816000] UBI: total number of reserved PEBs: 4004
      143. [ 3.817000] UBI: number of PEBs reserved for bad PEB handling: 40
      144. [ 3.818000] UBI: max/mean erase counter: 11/5
      145. [ 3.818000] UBI: image sequence number: 1796547544
      146. [ 3.819000] UBI: background thread "ubi_bgt0d" started, PID 54
      147. [ 3.826000] ALSA device list:
      148. [ 3.826000] No soundcards found.
      149. INIT: version 2.88 booting
      150. Starting udev
      151. starting version 230
      152. [ 4.487000] bcmdriver: module license 'Proprietary' taints kernel.
      153. [ 4.487000] Disabling lock debugging due to kernel taint
      154. [ 4.489000] BCMDRV: Initializing bcmdriver version $ 8
      155. [ 4.490000] BCMDRV: Total intc words=3,Total Irqs=97
      156. [ 4.492000] BCMDRV: Initialization complete
      157. bootlogd: cannot allocate pseudo tty: No such file or directory
      158. Tue Dec 1 11:07:52 UTC 2020
      159. INIT: Entering runlevel: 5
      160. Configuring network interfaces... [ 5.514000] ADDRCONF(NETDEV_UP): eth0: link is not ready
      161. udhcpc (v1.24.1) started
      162. Sending discover...
      163. [ 7.046000] bcmgenet bcmgenet.0: eth0: link up, 100 Mbps, full duplex
      164. [ 7.046000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
      165. Sending discover...
      166. Sending select for 10.255.251.111...
      167. Lease of 10.255.251.111 obtained, lease time 691200
      168. /etc/udhcpc.d/50default: Adding DNS 10.255.251.50
      169. /etc/udhcpc.d/50default: Adding DNS 10.255.251.1
      170. done.
      171. Starting Dropbear SSH server: Generating key, this may take a while...
      172. Public key portion is:
      173. ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAABAQCHAog8Rv0j6lvAURsi1ya7b39rnVOjvisv2h37+iJApSk0AHH0tTIfG7rosACBIe21IRGXjwFCmrMr+NQumIax5y5hTYCbGn2sdyL+FcE7NBF9N9prf6KPZWgKksInQ22T/NXIzVqo2wqtUoHAw5sowC4+8KV3x+lJLA7/9VHKY49Vy9Yp+re/s2/3Gndm1MvVnwDcIxxSVizOqnLuq6Pa2gacn0ou2hfMRNlMe4Yr0zf065TmRdWzv+hLznhyMrI8K1ZcZxGiAd25iqNN9qRbcBULE7kZPAXmXxEKVkq+cTmnGH+OeqLtQLgo9xspDs0SRtd2g+fAc2wYty0viKh/ root@dm520
      174. Fingerprint: md5 a5:0e:7c:8f:36:ea:08:da:fb:c3:ed:b9:2f:50:c5:7b
      175. dropbear.
      176. Starting autoflashd.
      177. Starting recovery-ui.
      178. Starting tpmd.
      179. Starting internet superserver: xinetd.
      180. Starting Lighttpd Web Server: lighttpd.
      181. 2020-12-01 11:08:28: (../../lighttpd-1.4.39/src/log.c.194) server started
      182. opendreambox 2.5.0 dm520 /dev/ttyS0
      183. >>> Your Dreambox has booted into RESCUE MODE.
      184. >>> Please log in as user 'root' (no password required),
      185. >>> then run 'help' to get further information.
      186. dm520 login:
      Alles anzeigen


      Kartenali schrieb:

      Kannst du mal folgendes machen über putty ??

      fdisk -lu /dev/mmcblk0
      blkid|grep mmcblk0

      @Kartenali


      soeben ausgeführt:



      dm520 login: root
      login[370]: root login on 'ttyS0'
      root@dm520:~# fdisk -lu /dev/mmcblk0
      fdisk: can't open '/dev/mmcblk0': No such file or directory
      root@dm520:~# blkid|grep mmcblk0
      [ 68.449000] brcmnand brcmnand.0: bitflips oob(120) data(4088) at 0x1fe7e000
      [ 68.450000] brcmnand brcmnand.0: uncorrectable error at 0x1fe7e000
      [ 68.451000] end_request: I/O error, dev mtdblock1, sector 1045488
      [ 68.451000] Buffer I/O error on device mtdblock1, logical block 130686
      [ 68.453000] brcmnand brcmnand.0: bitflips oob(120) data(4088) at 0x1fe7e000
      [ 68.454000] brcmnand brcmnand.0: uncorrectable error at 0x1fe7e000
      [ 68.455000] end_request: I/O error, dev mtdblock1, sector 1045488
      [ 68.455000] Buffer I/O error on device mtdblock1, logical block 130686
      root@dm520:~#
      Kannst Du nicht, willst Du nicht.......hast Du schon :P
      Zitat: »Wer zu lesen versteht, besitzt den Schlüssel zu großen Taten, zu unerträumten Möglichkeiten.«
    • Was mich stutzig macht ist folgender eintrag

      Quellcode

      1. [ 0.606000] brcmnand brcmnand.0: 512MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-4
      2. [ 0.606000]
      3. [ 0.609000] Bad block table found at page 261952, version 0x01
      4. [ 0.610000] brcmnand brcmnand.0: bitflips oob(80) data(1984) at 0x1ffe0000
      5. [ 0.611000] brcmnand brcmnand.0: uncorrectable error at 0x1ffe0600
      6. [ 0.613000] Bad block table found at page 261888, version 0x01
      7. [ 0.614000] nand_read_bbt: bad block at 0x000005780000
      8. [ 0.615000] nand_read_bbt: bad block at 0x0000057c0000
      9. [ 0.615000] nand_read_bbt: bad block at 0x000010180000
      10. [ 0.616000] nand_read_bbt: bad block at 0x0000101a0000
      11. [ 0.617000] nand_read_bbt: bad block at 0x00001ffc0000
      12. [ 0.617000] nand_read_bbt: bad block at 0x00001ffe0000
      13. [ 0.629000] Creating 3 MTD partitions on "brcmnand.0":
      14. [ 0.629000] 0x000000000000-0x00001f500000 : "rootfs"
      15. [ 0.632000] 0x000000000000-0x000020000000 : "entire_device"
      16. [ 0.634000] 0x00001f500000-0x00001fa00000 : "kernel"
      Alles anzeigen
      brcmnand brcmnand.0: uncorrectable error at 0x1ffe0600


      Die Befehle waren für DM 920/900


      fdisk -lu /dev/mmcblk0
      blkid|grep mmcblk0

      Kann sein das es in der Dream 520 einen anderen Namen hat da er Sie nicht findet
      Sieht aber so aus als wenn die Partitionen neu erstellt werden oder es zumindest Versucht wird laut dem Log

      Habe keine 520 hier um das mal zu Vergleichen
    • Kann ich leider nicht sagen.
      Habe für mich eig. immer die DM800er, DM820, DM900, DMTwo.

      Die DM525er und die 520er habe ich für bekannte Organisiert.

      Und ich habe 6x Stück DM525er gebraucht gekauft. Image war drauf.
      Sogar das Orig. Mache Update auf der BOX mit der Fernbedienung.
      Und alle 6x Boxen rot LED und im Rescue Mode.

      Daher gestern bei Amazon eine 520er Bestellt.
      Heute gekommen und exakt das gleiche hier.
      Nur bei der 520er komme ich noch via Browser und Putty auf die Box.

      Habe schon eine E-Mail an Dreambox geschrieben was da los ist.
      Evenutell schon wieder eine gewisse Mainboard Serie Defekt wie damals bei der DM900er ?

      Ich mein habe Dreamboxen seit der DM600 im Einsatz und hatte noch nie solche Probleme.
      Kannst Du nicht, willst Du nicht.......hast Du schon :P
      Zitat: »Wer zu lesen versteht, besitzt den Schlüssel zu großen Taten, zu unerträumten Möglichkeiten.«
    • hast du den schon Versucht das Original Image von Dream zu Flashen ???

      dreamboxupdate.com/opendreambo…deb-dm520-20211029.tar.xz

      über den Rescue Loader kommst du da noch auf die Web Oberfläche ???

      ansonsten über Putty
      to-the-rescue
      bei 1-2 Boxen hätte ich ja noch gesagt ok Hardware Fehler aber hier sieht es eher so aus als wenn die Aktuellen Images das System Zerschießen ob es nun eine Kombination aus Image und Loader ist ???oder ob die Images speicherbereiche der Box ansprechen mal spasseshalber ein alte Image Flashen für die 520 ob das geht ??
    • Ja wurde alles schon gemacht.
      Alle Boxen.

      Und immer das Aktuellste Image Heruntergeladen von DM bzw. NN².
      Bei der Box von Heute (Amazon) kam ich auf die WEBGUI (Flashen) drauf und via Putty sogar mit Service Port.
      Bei d. gebrauchten 525er nicht.

      Habe bei Amazon jetzt ein Ersatz Produkt angefordert und kommt am Montag.
      Das Teste ich nochmal durch.

      Welche Loader drauf ist usw.....
      Werde das auch sauber mitschreiben.

      Bin gespannt was DM retour schriebt auf meine Mail.
      Kannst Du nicht, willst Du nicht.......hast Du schon :P
      Zitat: »Wer zu lesen versteht, besitzt den Schlüssel zu großen Taten, zu unerträumten Möglichkeiten.«

      Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von Darksniper ()

    • Habe ich auch schon gemacht.
      Images ab 2017.
      Habe sogar den Rescue Loader von 2017 auf die Box Installiert via Putty.
      Nicht mal das hat funktioniert.

      Die 520er Box kam heute mit dem Loader 103. Dann Setup von DM ausgeführt. Update Reboot.
      LED rot.

      Online Recovery => Nein.
      NN² Image => Nein.

      Dann Spielerei mit Rescue Update via putty, ok.
      Wieder Online Recovery => Nein
      NN² Image => Nein

      Image NN² 2.0 und von DM => Nein.

      Update LOG bei allen Images gleich kein unterschied.

      Am schluß durch Putty Update 104 Loader, ok
      Dann wieder Test mit Images bze. mit Hilfe v. euch.

      Leider alles ohne erfolg.

      ----------------------------------------

      Box ist schon wieder eingepackt.

      Wenn am Montag die Ersatz DM520 da ist.

      Gehe ich vor wie folgt.
      Auspacken
      DM Image Setup ausführen. Ohne Reboot und Update.
      Check Device Info. Loader usw.
      Dann Update Orig. DM Image und Reboot....
      dann gucken ob Box Defekt wird oder nicht.
      Danach Update Loader und dann die Images.....
      Kannst Du nicht, willst Du nicht.......hast Du schon :P
      Zitat: »Wer zu lesen versteht, besitzt den Schlüssel zu großen Taten, zu unerträumten Möglichkeiten.«
    • Auch wenn es sich ganz Blöd anhört versuch mal Ohne Frontpanel zu Flashen und mit Abgezogenen Kabeln HDMI, LAN
      Über die Serielle USB Schnitstelle der BOX
      Wäre nicht das erste mal das es dannach wieder geht

      jb8a8f8.com/support/index.php?…et-utf-8-problem-etc.615/

      jb8a8f8.com/support/index.php?threads/dm520hd-nand.734/
    • Beide hacken waren draussen, Jap.
      Test via Browser Google Chrome und Mozilla Firefox.
      Ich habe heute nach dem fehler via Putty Online geflashed ohne Frontpanel und Co.
      Bin das schon alles durchgegangen.

      Flashen Only Seriell habe ich nicht gemacht.
      Könnte ich Testen am Montag.

      ----------------------------------------

      Info:
      Habe Dreambox eine ausführliche E-Mail geschrieben (wegen 525er un der 520) sowie auch mit Ihnen telefoniert.
      Das quasi 7 Boxen nach dem DM Update quasi Defekt sind.
      Angbelich wird die Entwicklung d. Fall Prüfen, ob es eventuell ein Problem gibt mit dem Update oder sonstiges.

      Des weiteren die Neue Ersatz DM520 v. Amazon ist gerade angekommen.
      Aber muss noch warten die DM520 ist Eiskalt.
      Kannst Du nicht, willst Du nicht.......hast Du schon :P
      Zitat: »Wer zu lesen versteht, besitzt den Schlüssel zu großen Taten, zu unerträumten Möglichkeiten.«
    • Danke für die Infos

      Dann müssten sich ja noch einige melden wegen den gleichen Problem ???
      Was mich nur irritiert ist das es scheint als wenn das Flash nach den Update nicht gelesen werden kann bzw. Fehler meldet.

      Hast du es mal mit einem anderen PC Versucht und eventuell nur Switch und Box ???
      Nicht das etwas am Netzwerk die Daten welche zur Box gesendet werden Versaut ???
      Hatte so etwas mal gesehen als jemand an den Einstellungen der Netzwerkkarte bei einer Intel Herumgespielt hatte. Da gab es ein Phänomen das Pakete Fehlerhaft waren
      Auch einige SSD der älteren Generation hatten mal solche Fehler verursacht ( Notfalls Firmware Update machen) falls die Vermutung dort liegt)

      Kann vieles sein deshalb auch die empfehlung es mit einem anderen PC zu Versuchen
    • Hi,

      IT Fehler, Netzwerk usw. kann ich alles ausschließen. Ebenfalls Firewall Cluster wird nix geblockt (IT Umgebung) :)

      ----------------------------------------

      Dreambox Setup Start, ok
      Laut System Info:
      Dreambox OS:4.3.2r7.17-g32f8eb-2019-08-30
      Image Release:2019-09-11


      Via GUI in d. Wiederherstellungsmodus gewechselt, ok
      DM520 Rescue Loader #103
      Product name DM520
      Rescue Loader version 103
      Flash size 512 MiB
      Production date 20210715
      mID 21
      Serial number XXXXX
      MAC address XXXXX
      Printed serial number XXXXXX


      Online Recovery ausgeführt.
      Beide Hacken sind raus.

      Quellcode

      1. Console Log:
      2. [*] Downloading 'http://dreamboxupdate.com/download/recovery/dm520/release/recovery.sig'
      3. [*] Downloading 'http://dreamboxupdate.com/download/recovery/dm520/release/recovery'
      4. [*] Verifying signature of 'recovery'
      5. gpgv: Signature made Wed Dec 21 02:01:50 2016 UTC using RSA key ID A07683D3
      6. gpgv: Good signature from "Dreambox DM520 Recovery <dm520@recovery.dreambox.de>"
      7. [*] Verifying signature of '/data/.recovery/recovery'
      8. [*] Running './recovery'
      9. [*] Options '-v'
      10. [*] Downloading 'http://dreamboxupdate.com/download/recovery/dm520/release/dreambox-image-dm520.tar.xz.sig'
      11. [*] Downloading 'http://dreamboxupdate.com/download/recovery/dm520/release/dreambox-image-dm520.tar.xz'
      12. [*] Verifying signature of 'dreambox-image-dm520.tar.xz'
      13. gpgv: Signature made Thu Nov 14 16:41:51 2019 UTC using RSA key ID A07683D3
      14. gpgv: Good signature from "Dreambox DM520 Recovery <dm520@recovery.dreambox.de>"
      15. [*] Removing volume 0 from /dev/ubi0
      16. [*] Creating volume 0 on /dev/ubi0 (dreambox-rootfs)
      17. Set volume size to 502571008
      18. Volume ID 0, size 3958 LEBs (502571008 bytes, 479.3 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "dreambox-rootfs", alignment 1
      19. [*] Creating ubifs filesystem on /dev/ubi0_0
      20. [*] Mounting '/dev/ubi0_0' to '/mnt'
      21. [*] Extracting 'dreambox-image-dm520.tar.xz' to '/mnt'
      22. [*] Mounting '/dev' to '/mnt/dev'
      23. [*] Mounting '/proc' to '/mnt/proc'
      24. [*] Mounting '/run' to '/mnt/run'
      25. [*] Mounting '/sys' to '/mnt/sys'
      26. [*] Mounting '/tmp' to '/mnt/tmp'
      27. Manufacturer ID: c2
      28. Memory type : 20
      29. Memory density : 18
      30. read id ok
      31. comparing 98 sectors...
      32. erasing 1 sectors...
      33. writing 16 pages...
      34. verifying 1 sectors...
      35. flash done
      36. update-alternatives: error: cannot append to '/var/log/alternatives.log': No such file or directory
      37. [*] Erasing flash memory on /dev/mtd2
      38. [*] Writing to NAND memory on /dev/mtd2
      39. [*] Unmounting '/mnt/dev'
      40. [*] Unmounting '/mnt/proc'
      41. [*] Unmounting '/mnt/run'
      42. [*] Unmounting '/mnt/sys'
      43. [*] Unmounting '/mnt/tmp'
      44. [*] Unmounting '/mnt'
      45. [*] Finished successfully. You may reboot now.
      46. [*] Initiating reboot
      Alles anzeigen



      Reboot war ok.
      Dreambox Setup Start, ok
      Laut System Info:
      Dreambox OS:4.3.2r7.17-g32f8eb-2019-08-30
      Image Release:2019-09-11


      Via GUI in d. Wiederherstellungsmodus gewechselt, ok


      DM520 Rescue Loader #103
      Product name DM520
      Rescue Loader version 103
      Flash size 512 MiB
      Production date 20210715
      mID 21
      Serial number XXXXX
      MAC address XXXXX
      Printed serial number XXXXXX


      Rescue Loader version 103 => noch nicht auf der Version 104.


      Unterschied zu dieser DM520 und der anderen DM520 ist das Production date die jetztige 2021 die ander 2022 und der Rescue Loader.


      Habe vom DM Website die Stable Images angeschaut:
      wget dreamboxupdate.com/opendreambox/2.5/stable/images/dm520/vmlinux.gz-rescue-3.4-r1-dm520-20200715.bin
      flash-rescue vmlinux.gz-rescue-3.4-r1-dm520-20200715.bin

      Quellcode

      1. root@dm520:~# wget dreamboxupdate.com/opendreambox/2.5/stable/images/dm520/vmli nux.gz-rescue-3.4-r1-dm520-20200715.bin
      2. Connecting to dreamboxupdate.com (178.19.67.219:80)
      3. vmlinux.gz-rescue-3. 100% |*******************************| 11228k 0:00:00 ETA
      4. root@dm520:~# flash-rescue vmlinux.gz-rescue-3.4-r1-dm520-20200715.bin
      5. Manufacturer ID: c2
      6. Memory type : 20
      7. Memory density : 18
      8. read id ok
      9. comparing 2808 sectors...
      10. erasing 2808 sectors...
      11. writing 44928 pages...
      12. verifying 2808 sectors...
      13. flash done
      14. root@dm520:~#reboot
      Alles anzeigen

      Reboot war ok.
      Via GUI in d. Wiederherstellungsmodus gewechselt, ok


      Rescue Loader Version nach wie vor 103.
      Box funktioniert soweit Fehlerfrei.


      Starte Box Neu.
      Und versuche mit Orig. Image => Image Update/Software Aktualisierungen...
      die Pakete wurden schnell geladen...
      nur bei new hat es länger gedauert...
      In Summe 54 Pakete
      Reboot ...
      Soweit alles ok.
      Via GUI in d. Wiederherstellungsmodus gewechselt, ok
      Rescue Loader nach wie vor auf 103.


      Boote wieder ins Image und versuche Rescue Loader Update via Putty mit "update-rescue -v"

      Quellcode

      1. root@dm520:~# update-rescue -v
      2. [*] Downloading 'http://dreamboxupdate.com/download/recovery/dm520/release/rescue-image-dm520.bin.sig'
      3. [*] Downloading 'http://dreamboxupdate.com/download/recovery/dm520/release/rescue-image-dm520.bin'
      4. [*] Verifying signature of 'rescue-image-dm520.bin'
      5. gpgv: Signature made Mon Dec 2 22:50:06 2019 CET using RSA key ID A07683D3
      6. gpgv: Good signature from "Dreambox DM520 Recovery <dm520@recovery.dreambox.de>"
      7. [*] Writing rescue image to flash
      8. Manufacturer ID: c2
      9. Memory type : 20
      10. Memory density : 18
      11. read id ok
      12. comparing 2809 sectors...
      13. erasing 2808 sectors...
      14. writing 44928 pages...
      15. verifying 2808 sectors...
      16. flash done
      17. [*] Done.
      18. root@dm520:~# reboot
      Alles anzeigen
      Reboot war, ok



      Via GUI in d. Wiederherstellungsmodus gewechselt, ok
      Rescue Loader nach wie vor auf 103.


      Also komisch heute ändert sich der Loader nicht !!
      Kannst Du nicht, willst Du nicht.......hast Du schon :P
      Zitat: »Wer zu lesen versteht, besitzt den Schlüssel zu großen Taten, zu unerträumten Möglichkeiten.«
    • Sollte ich jetzt mal das NN² Image drauf machen ?
      Was meint ihr.

      ----------------------------------------

      Lade erneut das Image herunter:




      ----------------------------------------

      Download NN² Image
      Upload via Browser beide hacken raus.
      Console Log:

      Quellcode

      1. [*] Removing volume 0 from /dev/ubi0
      2. [*] Creating volume 0 on /dev/ubi0 (dreambox-rootfs)
      3. Set volume size to 502571008
      4. Volume ID 0, size 3958 LEBs (502571008 bytes, 479.3 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "dreambox-rootfs", alignment 1
      5. [*] Creating ubifs filesystem on /dev/ubi0_0
      6. [*] Mounting '/dev/ubi0_0' to '/mnt'
      7. [*] Extracting '/tmp/DgqCcC' to '/mnt'
      8. [*] Mounting '/dev' to '/mnt/dev'
      9. [*] Mounting '/proc' to '/mnt/proc'
      10. [*] Mounting '/run' to '/mnt/run'
      11. [*] Mounting '/sys' to '/mnt/sys'
      12. [*] Mounting '/tmp' to '/mnt/tmp'
      13. Manufacturer ID: c2
      14. Memory type : 20
      15. Memory density : 18
      16. read id ok
      17. comparing 98 sectors...
      18. nothing to do
      19. update-alternatives: error: cannot append to '/var/log/alternatives.log': No such file or directory
      20. [*] Erasing flash memory on /dev/mtd2
      21. [*] Writing to NAND memory on /dev/mtd2
      22. [*] Unmounting '/mnt/dev'
      23. [*] Unmounting '/mnt/proc'
      24. [*] Unmounting '/mnt/run'
      25. [*] Unmounting '/mnt/sys'
      26. [*] Unmounting '/mnt/tmp'
      27. [*] Unmounting '/mnt'
      28. [*] Finished successfully. You may reboot now.
      Alles anzeigen

      Reboot via Browser....
      Box Startet gerade...
      bin jetzt beim Wizard.

      ----------------------------------------

      Setup Wizard ausgeführt.
      inkl. CAMD Install.
      danach gleich Info 83 Updates Verfügbar.
      JA
      Donwload und Upgrade wird ausgeführt....
      Reboot.


      Box hat Normal gestartet.
      Laut System Info: Bild im Anhang

      Soweit schaut heute alles gut aus.
      Bilder
      • SysInfo.JPG

        37,76 kB, 565×420, 62 mal angesehen
      Kannst Du nicht, willst Du nicht.......hast Du schon :P
      Zitat: »Wer zu lesen versteht, besitzt den Schlüssel zu großen Taten, zu unerträumten Möglichkeiten.«