500 Hd+usb

    • Original von JERKBALL
      Wenn man es genau nimmt, ist das wohl ein fest installierter Serial2USB Anschluss, über den die Log Ausgabe realisiert wurde....


      genau getroffen. :)
      "Remember, if it's psychobilly, it's gotta have some rockabilly in it somwhere. It ain't just punk with a double bass." (P.Paul Fenech)

    • Hallo

      Habe den oben genannten adapter und die dm500hd

      kann aber die HDD per usb mit externe stromquelle nicht finden

      muss ich da noch was mounten oder freigeben damit er die platte findet?

      danke im voraus

      Riddick

    • Kannst Du denn irgendwas an den Adapter anschliessen, was erkannt wird? z.B. USB-Stick, WLAN-Stick? Wenn nicht denke ich mal das dieser Adapter einfach nicht an der Box funktioniert um auf USB umzusetzen.
      "Remember, if it's psychobilly, it's gotta have some rockabilly in it somwhere. It ain't just punk with a double bass." (P.Paul Fenech)

    • Morgen

      Also

      USB stick geht nicht

      Wlan habe ich nicht probiert denke es geht aber auch nicht (weil kein strom anliegt über eSata)

      Externe HDD mit Stromanschluß geht auch nicht.

      Schade

      Habe gedacht mir den kauf von einer Externen Sataplatte zu ersparen.

      Gruß

      Riddick

    • Die Usb-Schnittstellen sind scheinbar rausgeführt (Kontaktpins oberhalb des Cardreaders) aber grundlegend deaktiviert (First bzw Second Stage Loader?) ala interne Usb-Buchse der DM800.

      Es bleibt wohl auf absehbare Zeit nix anderes übrig, bei "Usb-Wünschen" die DM8000 oder die langsame DM800 zu kaufen...

    • Hallo zusammen,

      habe es im Netz gefunden,

      falls es nicht erlaubt wird dann löschen:)


      Howto Enable USB on DM500hd

      Here is the guide to activate Usb controller on your DM500hd with a little hardware modification.
      Warning: Removing resistors means you are going to VOID WARRANTY and everything happening since then will be at YOUR OWN RISK, no one will take responsibility for your own actions.
      4fun: This guide is free and you can redistribute for every forums


      Enabling USB port on DM500HD

      On DM500HD there is a standard usb pinheader, but the usb controller has been fixed into a disable
      state, because it misses an over-current protection on 5v pins (max1823 on dm800 for example) and
      so it does not meet usb specs.
      Removing a resistor (or two), you can fake the presence of such missing chip, but in case your usb
      device makes a short, there will be no protection against flaming the main 5v mainboard regulator,
      you can imagine what could happen. If usb specs requires an overcurrent protection, there must be a
      good reason afterall.
      Removing resistors means you are going to VOID WARRANTY and everything happening since
      then will be at YOUR OWN RISK, no one will take responsibility for your own actions.


      img121.imageshack.us/img121/8814/46412886.png


      You can see here the standard PC motherboard usb pinheader with a standard PC usb bracket
      connected. The bottom-right pin is in real disconnected, you have to make an hole into the PC
      bracket connector to let it feet. On the rear panel of the decoder, there is a pre-cut window for a
      single usb female connector, if you want a stylish job.


      img521.imageshack.us/img521/3355/16529487.png


      In my decoder there was only R1011 populated with a 0ohm resistor, but in case you have R1010
      populated or both, you have to remove both. These are FAULTA and FAULTB signals that would
      come from the missing max1823 usb power control switch, it’s enough to have one populated to
      tell the Broadcom to disable the whole usb controller.


      img521.imageshack.us/img521/1017/30627888.png


      Looking at usb specs, the device that must handle the over-current protection is the hub, so, instead
      of directly connecting an usb device, I would suggest to buy a good usb external-powered hub
      which reports “over-current protection” on the specs, because the cheap chinese ones does not have
      a dedicated power control circuit. Googling a little, hubs with Genesys GL850 chip seem good
      candidates.


      img171.imageshack.us/img171/6452/53445991.png


      Gruß

      GAMA007

    • usb an 500 hd

      abei PDF file fuer umbau dm 500 hd zu USB extern .( fremdforum) :)

      mfg
      Dateien
      3 stk Dreambox 8000 - 7080 - One -Samsung 65" Full HD TFT - Denon 4308 AMP- T90 -> 42E - 28.2E - 23.5E - 19.2E - 13E - 9E - 7E - 5E - 1W - 4W -5W -8W - 12.5W

      1100 mbit Static IP