Angepinnt OE2.5: Rückmeldungen zum weekly Image für DM520/DM525/DM820 und DM7080
-
-
Das letzte Update habe ich Gestern über Connsole gemacht.
apt-get update
apt-get upgrade
Das läuft problemlos durch
LG, Snake,,,,
(o o)
---o0O--(_)--O0o---
Billy is watching you... -
... werden die alias damit nicht auch aktualisiert? Oder warum muss das Snake48 manuell updaten?
-
Ich hatte diese Problem auch mal und dies war die Lösung
Da ging wohl bei einem update etwas schief . -
Hilfsbereit schrieb:
... werden die alias damit nicht auch aktualisiert? Oder warum muss das Snake48 manuell updaten?
Es lag an den "alias"
LG, Snake,,,,
(o o)
---o0O--(_)--O0o---
Billy is watching you... -
ist ja logisch, dass es jetzt wieder geht. Mit den Befehlen von Joey und Mausi wurden die alias ja auch aktualisiert. Ich hätte nur angenommen, das hätte ein voriges Image-Update schon mit erledigen müssen .
-
Snake48 schrieb:
Das letzte Update habe ich Gestern über Connsole gemacht.
apt-get update
apt-get upgrade
Wenn so, dann bitte per
apt-get update
apt-get dist-upgrade -
Joey schrieb:
Snake48 schrieb:
Das letzte Update habe ich Gestern über Connsole gemacht.
apt-get update
apt-get upgrade
apt-get update
apt-get dist-upgrade
LG, Snake,,,,
(o o)
---o0O--(_)--O0o---
Billy is watching you... -
up ist in jedem Fall besser. Da werden auch noch ein paar andere Sachen ausgeführt. Also entweder per Paketmanager oder wenn per Konsole, dann mit up updaten
-
Ich habe den Eindruck, dass die Box (DM525) seit dem letzten Upgrade deutlich langsamer bootet, als vorher. Ist es nur bei mir so?
-
Hallo,
ich wollte meine Box Updaten
diese Meldung kommt
dpkg was interrupted, you must manually run 'dpkg --configure -a' to correct the problem
beim Updaten.
Was ist das für eine Meldung.
Meine Box ist 7080HD Image von 25.07.2017 -
Nur mal zur Info. Seit den letzten beiden dicken Updates der enigma2-Versionen startet OSCam auf der 7080 bei mir nur mit einer delay-Einstellung von 10 Sekunden (weniger habe ich nocht nicht probiert). Auf der 900 startet OSCam wie immer normal ohne delay. Vor den Updates brauchte ich auf der 7080 auch kein delay.
Ich benutze die oscam-modern vom Feed, überschreibe die oscam aber mit meiner selbst-s3-compilierten Version.
saki schrieb:
dpkg --configure -a
Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von Griffel ()
-
goliath schrieb:
Nur mal zur Info. Seit den letzten beiden dicken Updates der enigma2-Versionen startet OSCam auf der 7080 bei mir nur mit einer delay-Einstellung von 10 Sekunden (weniger habe ich nocht nicht probiert). Auf der 900 startet OSCam wie immer normal ohne delay. Vor den Updates brauchte ich auf der 7080 auch kein delay.
Ich benutze die oscam-modern vom Feed, überschreibe die oscam aber mit meiner selbst-s3-compilierten Version.
saki schrieb:
dpkg --configure -a
Gruß
blue cult -
Blaue Taste - newnigma2 services - emu menü - camd Einstellungen
Hier kannst du ein delay einstellen -
Schnelleinstieg zu den aktuellen OE2.5 Images (DM520/525, DM820HD, DM7080HD, DM900UHD)
Joey schrieb:
Das Softcam startet nach einem Neustart der Box nicht
blaue Taste > Newnigma2 Services > EMU Menü > Camd Einstellungen > Camd start delay on bootup > 10 seconds > grüne Taste, danach Neustart der Box
-
Guten Abend,
die Uhrzeit meiner DM820HD geht 5 Min. vor, wie kann ich das korrigieren?
Grüße Grilletta -
-
Auf "Das Erste" schalten, Box herunterfahren, für 5 Minuten vom Strom trennen, Strom wieder einstecken
-
Seit den letzten Updates findet meine DM820 kaum noch Sender. Auf Astra 23.5 wird plötzlich gar nichts mehr gefunden? Weiß jemand Rat?
Thx. -
Joey schrieb:
Schnelleinstieg zu den aktuellen OE2.5 Images (DM520/525, DM820HD, DM7080HD, DM900UHD)
Joey schrieb:
Das Softcam startet nach einem Neustart der Box nicht
blaue Taste > Newnigma2 Services > EMU Menü > Camd Einstellungen > Camd start delay on bootup > 10 seconds > grüne Taste, danach Neustart der Box
Hatte es nicht ignoriert, sondern nicht gesehen. Klappt alles. Nochmals danke.Gruß
blue cult
-
Teilen
- Facebook 0
- Twitter 0
- Google Plus 0
- Reddit 0
-
Benutzer online 45
45 Besucher